Your free source for specifications, standards, and handbooks
USAF - Tech Manuals
TO 00-20-1 TECHNICAL MANUAL AEROSPACE EQUIPMENT MAINTENANCE INSPECTION, DOCUMENTATION, POLICIES, AND PROCEDURES (CHANGE 4 - 1 SEPTEMBER 2006)
TO 00-20-1 TECHNICAL MANUAL AEROSPACE EQUIPMENT MAINTENANCE INSPECTION, DOCUMENTATION, POLICIES, AND PROCEDURES (CHANGE 4 - 1 SEPTEMBER 2006). This Technical Order (TO) establishes the policies and procedures for use of the 00-20- series TOs and provides weapon system and equipment maintenance inspection and documentation guidance. It also implements the policies of AFI 21-101, Aerospace Equipment Maintenance Management; AFI 21-116, Maintenance Management of Communications- Electronics; and AFI 11-301, Aircrew Life Support (ALS) Program; and AFI 21-102, Depot Maintenance Management. 1.1.2 Unless otherwise specified, the term “AEROSPACE EQUIPMENT” in this technical order refers to weapon systems and equipment such as aerospace vehicles, equipment, missiles, nuclear weapons, Test Measurement and Diagnostic Equipment (TMDE), ground Communications-Electronics (C-E) equipment, trainers, training equipment, engines, life support equipment (LSE), industrial plant equipment, all related support equipment (SE). This technical order is applicable to all organizations maintaining this equipment.
Ident. Num:
TO 00-20-1
Rev. Num:
-
TO 00-20-1 TECHNICAL MANUAL AEROSPACE EQUIPMENT MAINTENANCE INSPECTION, DOCUMENTATION, POLICIES, AND PROCEDURES (CHANGE 4 - 1 SEPTEMBER 2006). This Technical Order (TO) establishes the policies and procedures for use of the 00-20- series TOs and provides weapon system and equipment maintenance inspection and documentation guidance. It also implements the policies of AFI 21-101, Aerospace Equipment Maintenance Management; AFI 21-116, Maintenance Management of Communications- Electronics; and AFI 11-301, Aircrew Life Support (ALS) Program; and AFI 21-102, Depot Maintenance Management. 1.1.2 Unless otherwise specified, the term “AEROSPACE EQUIPMENT” in this technical order refers to weapon systems and equipment such as aerospace vehicles, equipment, missiles, nuclear weapons, Test Measurement and Diagnostic Equipment (TMDE), ground Communications-Electronics (C-E) equipment, trainers, training equipment, engines, life support equipment (LSE), industrial plant equipment, all related support equipment (SE). This technical order is applicable to all organizations maintaining this equipment.
TO 00-20-14, TECHNICAL MANUAL AIR FORCE METROLOGY AND CALIBRATION PROGRAM (30 JUN 2007)
TO 00-20-14, TECHNICAL MANUAL AIR FORCE METROLOGY AND CALIBRATION PROGRAM (30 JUN 2007)., This Technical Order (TO) contains the methods and procedures for the management of the Air Force Metrology and Calibration (AFMETCAL) Program. This TO implements AFI 21-113, Air Force Metrology and Calibration (AFMETCAL) Program.
Ident. Num:
TO 00-20-14
Rev. Num:
-
TO 00-20-14, TECHNICAL MANUAL AIR FORCE METROLOGY AND CALIBRATION PROGRAM (30 JUN 2007)., This Technical Order (TO) contains the methods and procedures for the management of the Air Force Metrology and Calibration (AFMETCAL) Program. This TO implements AFI 21-113, Air Force Metrology and Calibration (AFMETCAL) Program.
TO 00-20-2, TECHNICAL MANUAL MAINTENANCE DATA DOCUMENTATION (CHANGE 2 - 15 APRIL 2007)
TO 00-20-2, TECHNICAL MANUAL MAINTENANCE DATA DOCUMENTATION (CHANGE 2 - 15 APRIL 2007). The purpose of this Technical Order (TO) is to provide a broad understanding of the objectives, scope, concept, and policy of Maintenance Data Documentation (MDD), and some intended uses of the data it contains. It prescribes the rules for documenting entries on weapon systems, support systems, and equipment that has been selected for reporting by the equipment manager, as indicated by the MICAP/MDD/TCTO settings on the Standard Reporting Designator (SRD). This TO also explains the Visibility and Management of Operating and Support Cost (VAMOSC), Core Automated Maintenance System (CAMS), Improved Maintenance Management Program (IMMP), Precision Measurement Equipment Laboratory Automated Management System (PAMS), CAMS for Mobility (GO81), Reliability and Maintainability Information System (REMIS), and Comprehensive Engine Management System (CEMS). It provides an authoritative source for certain codes used and entries required in the MDD process, reporting rules, and documentation for cannibalization actions. TO 00-20-2 provides policy and/or guidance for the individual maintenance activities (Chapter 8) for the collection and documentation of maintenance data.
Ident. Num:
TO 00-20-2
Rev. Num:
-
TO 00-20-2, TECHNICAL MANUAL MAINTENANCE DATA DOCUMENTATION (CHANGE 2 - 15 APRIL 2007). The purpose of this Technical Order (TO) is to provide a broad understanding of the objectives, scope, concept, and policy of Maintenance Data Documentation (MDD), and some intended uses of the data it contains. It prescribes the rules for documenting entries on weapon systems, support systems, and equipment that has been selected for reporting by the equipment manager, as indicated by the MICAP/MDD/TCTO settings on the Standard Reporting Designator (SRD). This TO also explains the Visibility and Management of Operating and Support Cost (VAMOSC), Core Automated Maintenance System (CAMS), Improved Maintenance Management Program (IMMP), Precision Measurement Equipment Laboratory Automated Management System (PAMS), CAMS for Mobility (GO81), Reliability and Maintainability Information System (REMIS), and Comprehensive Engine Management System (CEMS). It provides an authoritative source for certain codes used and entries required in the MDD process, reporting rules, and documentation for cannibalization actions. TO 00-20-2 provides policy and/or guidance for the individual maintenance activities (Chapter 8) for the collection and documentation of maintenance data.
TO 00-20-9, TECHNICAL MANUAL FORECASTING REPLACEMENT REQUIREMENTS FOR SELECTED CALENDAR AND HOURLY TIME CHANGE ITEMS (CHANGE 4 - 15 OCTOBER 2007)
TO 00-20-9, TECHNICAL MANUAL FORECASTING REPLACEMENT REQUIREMENTS FOR SELECTED CALENDAR AND HOURLY TIME CHANGE ITEMS (CHANGE 4 - 15 OCTOBER 2007). The procedures prescribed in this TO are applicable to the AFMC IM, ALC base support organizations, AF bases, Major Commands and requisitioning agencies. Security Assistance (SA) Program countries requisitioning items designated in this technical order from Air Force sources will comply with AF base reporting requirements.
Ident. Num:
TO 00-20-9
Rev. Num:
-
TO 00-20-9, TECHNICAL MANUAL FORECASTING REPLACEMENT REQUIREMENTS FOR SELECTED CALENDAR AND HOURLY TIME CHANGE ITEMS (CHANGE 4 - 15 OCTOBER 2007). The procedures prescribed in this TO are applicable to the AFMC IM, ALC base support organizations, AF bases, Major Commands and requisitioning agencies. Security Assistance (SA) Program countries requisitioning items designated in this technical order from Air Force sources will comply with AF base reporting requirements.
TO 00-20F-2, TECHNICAL MANUAL, INSPECTION AND PREVENTIVE MAINTENANCE PROCEDURES FOR CLASSIFIED STORAGE CONTAINERS (1 DEC 2006)
TO 00-20F-2, TECHNICAL MANUAL, INSPECTION AND PREVENTIVE MAINTENANCE PROCEDURES FOR CLASSIFIED STORAGE CONTAINERS (1 DEC 2006)., The purpose of this manual is to establish procedures for inspection and preventive maintenance of GSA approved security containers and vault doors authorized for storage of classified material.
Ident. Num:
TO 00-20F-2
Rev. Num:
-
TO 00-20F-2, TECHNICAL MANUAL, INSPECTION AND PREVENTIVE MAINTENANCE PROCEDURES FOR CLASSIFIED STORAGE CONTAINERS (1 DEC 2006)., The purpose of this manual is to establish procedures for inspection and preventive maintenance of GSA approved security containers and vault doors authorized for storage of classified material.
TO 00-5-1, TECHNICAL MANUAL AF TECHNICAL ORDER SYSTEM (1 FEB 1996)
TO 00-5-1, TECHNICAL MANUAL AF TECHNICAL ORDER SYSTEM (1 FEB 1996)., The purpose of this technical order (TO) is to describe the Air Force TO system established by Air Force Policy Directive (AFPD) 21-3, specify policies and responsibilities for operation and management of the TO system, and outline general procedures for use of the system. This TO identifies and explains the various types of TOs and the specific policies and procedures pertaining thereto.
Ident. Num:
TO 00-5-1
Rev. Num:
-
TO 00-5-1, TECHNICAL MANUAL AF TECHNICAL ORDER SYSTEM (1 FEB 1996)., The purpose of this technical order (TO) is to describe the Air Force TO system established by Air Force Policy Directive (AFPD) 21-3, specify policies and responsibilities for operation and management of the TO system, and outline general procedures for use of the system. This TO identifies and explains the various types of TOs and the specific policies and procedures pertaining thereto.
TO 00-5-16, TECHNICAL MANUAL SOFTWARE MANAGER'S MANUAL
TO 00-5-16, TECHNICAL MANUAL SOFTWARE MANAGER'S MANUAL USAF AUTOMATED COMPUTER PROGRAM IDENTIFICATION NUMBER SYSTEM (ACPINS) (15 OCTOBER 2003). The purpose of this Software Managers Manual is to provide information and guidance to effectively use the USAF Automated Computer Program Identification Number System (ACPINS). This manual is for use by software managers within the United States Air Force (USAF), Department of Defense (DoD) Agencies and Contractors, and Security Assistance (SA).
Ident. Num:
TO 00-5-16
Rev. Num:
-
TO 00-5-16, TECHNICAL MANUAL SOFTWARE MANAGER'S MANUAL USAF AUTOMATED COMPUTER PROGRAM IDENTIFICATION NUMBER SYSTEM (ACPINS) (15 OCTOBER 2003). The purpose of this Software Managers Manual is to provide information and guidance to effectively use the USAF Automated Computer Program Identification Number System (ACPINS). This manual is for use by software managers within the United States Air Force (USAF), Department of Defense (DoD) Agencies and Contractors, and Security Assistance (SA).
TO 00-5-17, TECHNICAL MANUAL USERS MANUAL USAF COMPUTER PROGRAM IDENTIFICATION NUMBERING (CPIN) SYSTEM (15 MAY 2003)
TO 00-5-17, TECHNICAL MANUAL USERS MANUAL USAF COMPUTER PROGRAM IDENTIFICATION NUMBERING (CPIN) SYSTEM (15 MAY 2003). The US Air Force has applied the principles of configuration management to software, providing the same degree of management control presently provided for hardware. ACPINS provides a system to identify, manage, requisition, and distribute MCS for NSS, which must be designated and managed as configuration items. Determination and designation of the CSCI is the responsibility of the software manager. A CSCI may consist of a single computer program, or a group of computer programs, which satisfies an end-use function. The configuration of a CSCI is identified through baseline documentation. The software manager may choose to identify the software at a level lower than the CSCI. The software item, either a CSCI, or a Computer Software Component (CSC), (both referred to in this manual as CSCIs), and related documentation will be assigned a CPIN. The data system that is used for assigning and controlling the CPIN is the USAF ACPINS.
Ident. Num:
TO 00-5-17
Rev. Num:
-
TO 00-5-17, TECHNICAL MANUAL USERS MANUAL USAF COMPUTER PROGRAM IDENTIFICATION NUMBERING (CPIN) SYSTEM (15 MAY 2003). The US Air Force has applied the principles of configuration management to software, providing the same degree of management control presently provided for hardware. ACPINS provides a system to identify, manage, requisition, and distribute MCS for NSS, which must be designated and managed as configuration items. Determination and designation of the CSCI is the responsibility of the software manager. A CSCI may consist of a single computer program, or a group of computer programs, which satisfies an end-use function. The configuration of a CSCI is identified through baseline documentation. The software manager may choose to identify the software at a level lower than the CSCI. The software item, either a CSCI, or a Computer Software Component (CSC), (both referred to in this manual as CSCIs), and related documentation will be assigned a CPIN. The data system that is used for assigning and controlling the CPIN is the USAF ACPINS.
TO 00-5-18 TECHNICAL MANUAL METHODS & PROCEDURES AF TECHNICAL ORDER NUMBERING SYSTEM (31 DECEMBER 2006)
TO 00-5-18 TECHNICAL MANUAL METHODS & PROCEDURES AF TECHNICAL ORDER NUMBERING SYSTEM (31 DECEMBER 2006). This technical order (TO) describes the procedures and techniques employed to assign TO numbers to technical data used to operate, install, maintain, inspect, perform procedural functions on, and modify Air Force weapons systems and equipment. Numbering techniques are not included in this TO for TO numbering assignments made according to waivers or deviations from established procedures.
Ident. Num:
TO 00-5-18
Rev. Num:
-
TO 00-5-18 TECHNICAL MANUAL METHODS & PROCEDURES AF TECHNICAL ORDER NUMBERING SYSTEM (31 DECEMBER 2006). This technical order (TO) describes the procedures and techniques employed to assign TO numbers to technical data used to operate, install, maintain, inspect, perform procedural functions on, and modify Air Force weapons systems and equipment. Numbering techniques are not included in this TO for TO numbering assignments made according to waivers or deviations from established procedures.
TO 00-5-19, TECHNICAL MANUAL SECURITY ASSISTANCE TECHNICAL ORDER PROGRAM (15 DEC 2003)
TO 00-5-19, TECHNICAL MANUAL SECURITY ASSISTANCE TECHNICAL ORDER PROGRAM (15 DEC 2003). This technical order (TO) outlines the policies and procedures of the United States Air Force (USAF) Security nce Technical Order Program (SATOP). The SATOP includes management procedures used by USAF, contractor, and foreign Air Force personnel for TO support of US Government-approved sales for military systems and commodities sold to foreign governments and international organizations under the Security Assistance Program (SAP). Support procedures for the Military Assistance Program (MAP), Foreign Military Sales (FMS), consortium and coproduction agreements, and direct commercial sales are included in this manual
Ident. Num:
TO 00-5-19
Rev. Num:
-
TO 00-5-19, TECHNICAL MANUAL SECURITY ASSISTANCE TECHNICAL ORDER PROGRAM (15 DEC 2003). This technical order (TO) outlines the policies and procedures of the United States Air Force (USAF) Security nce Technical Order Program (SATOP). The SATOP includes management procedures used by USAF, contractor, and foreign Air Force personnel for TO support of US Government-approved sales for military systems and commodities sold to foreign governments and international organizations under the Security Assistance Program (SAP). Support procedures for the Military Assistance Program (MAP), Foreign Military Sales (FMS), consortium and coproduction agreements, and direct commercial sales are included in this manual
TO 00-5-3, TECHNICAL MANUAL AF TECHNICAL MANUAL ACQUISITION PROCEDURES (1 APR 2001)
TO 00-5-3, TECHNICAL MANUAL AF TECHNICAL MANUAL ACQUISITION PROCEDURES (1 APR 2001)., This Air Force Technical Manual is dated 1 April 2001. It provides the TO Manager with guidance and direction for managing acquisition of TOs and updates, to support initial acquisition and modification os system and equipment hardware and software. TOs to support new acquisition or modification programs for military systems or commodities are acquired on a schedule formally imposed by the contract to meet the requirements for development, review, verification, and delivery of formal TOs. Any manuals developed for the government (at government expense) must be developed to a performance or government-approved non-governemnt specification.
Ident. Num:
TO 00-5-3
Rev. Num:
-
TO 00-5-3, TECHNICAL MANUAL AF TECHNICAL MANUAL ACQUISITION PROCEDURES (1 APR 2001)., This Air Force Technical Manual is dated 1 April 2001. It provides the TO Manager with guidance and direction for managing acquisition of TOs and updates, to support initial acquisition and modification os system and equipment hardware and software. TOs to support new acquisition or modification programs for military systems or commodities are acquired on a schedule formally imposed by the contract to meet the requirements for development, review, verification, and delivery of formal TOs. Any manuals developed for the government (at government expense) must be developed to a performance or government-approved non-governemnt specification.
TO 1-1-4, TECHNICAL MANUAL EXTERIOR FINISHES, INSIGNIA AND MARKINGS, APPLICABLE TO USAF AIRCRAFT (CHANGE 6 - 20 MAR 1998).
TO 1-1-4, TECHNICAL MANUAL EXTERIOR FINISHES, INSIGNIA AND MARKINGS, APPLICABLE TO USAF AIRCRAFT (CHANGE 6 - 20 MAR 1998)., The purpose of this technical order is to standardize the painting and marking configuration of exterior surfaces of all Air Force aircraft.
Ident. Num:
TO 1-1-4
Rev. Num:
-
TO 1-1-4, TECHNICAL MANUAL EXTERIOR FINISHES, INSIGNIA AND MARKINGS, APPLICABLE TO USAF AIRCRAFT (CHANGE 6 - 20 MAR 1998)., The purpose of this technical order is to standardize the painting and marking configuration of exterior surfaces of all Air Force aircraft.
TO 1-1A-1, TECHNICAL MANUAL ENGINEERING HANDBOOK SERIES FOR AIRCRAFT REPAIR GENERAL MANUAL FOR STRUCTURAL REPAIR
TO 1-1A-1, TECHNICAL MANUAL ENGINEERING HANDBOOK SERIES FOR AIRCRAFT REPAIR GENERAL MANUAL FOR STRUCTURAL REPAIR (15 NOV 06). THIS MANUAL SUPERSEDES NAVAIR 01-1A-1, DATED 1 MAY 2001, AND AF TO 1-1A-1, DATED 1 MARCH 1999, CHANGE 2 DATED 1 SEPTEMBER 2002. THIS IS THE FIRST ISSUE OF THIS MANUAL AS JOINT BETWEEN THE AIR FORCE AND NAVY. Technical Order (TO) 1-1A-1 is one of a series of manuals prepared to assist personnel engaged in the general maintenance and repair of military aircraft. This manual covers general aircraft structural repair.
Ident. Num:
TO 1-1A-1
Rev. Num:
-
TO 1-1A-1, TECHNICAL MANUAL ENGINEERING HANDBOOK SERIES FOR AIRCRAFT REPAIR GENERAL MANUAL FOR STRUCTURAL REPAIR (15 NOV 06). THIS MANUAL SUPERSEDES NAVAIR 01-1A-1, DATED 1 MAY 2001, AND AF TO 1-1A-1, DATED 1 MARCH 1999, CHANGE 2 DATED 1 SEPTEMBER 2002. THIS IS THE FIRST ISSUE OF THIS MANUAL AS JOINT BETWEEN THE AIR FORCE AND NAVY. Technical Order (TO) 1-1A-1 is one of a series of manuals prepared to assist personnel engaged in the general maintenance and repair of military aircraft. This manual covers general aircraft structural repair.
TO 1-1A-9,TECHNICAL MANUAL ENGINEERING SERIES FOR AIRCRAFT REPAIR AEROSPACE METALS - GENERAL DATA AND USAGE FACTORS (27 JUN 2005)
TO 1-1A-9,TECHNICAL MANUAL ENGINEERING SERIES FOR AIRCRAFT REPAIR AEROSPACE METALS - GENERAL DATA AND USAGE FACTORS (27 JUN 2005)., This technical manual provides precise data on specific metals to assist in selection, usage and processing for fabrication and repair. It includes such data as specification cross reference; approved designation system for alloys and tempers; temperatures and other controls for heat treatments; mechanical and physical properties forming characteristics; and other information.
Ident. Num:
TO 1-1A-9
Rev. Num:
5
TO 1-1A-9,TECHNICAL MANUAL ENGINEERING SERIES FOR AIRCRAFT REPAIR AEROSPACE METALS - GENERAL DATA AND USAGE FACTORS (27 JUN 2005)., This technical manual provides precise data on specific metals to assist in selection, usage and processing for fabrication and repair. It includes such data as specification cross reference; approved designation system for alloys and tempers; temperatures and other controls for heat treatments; mechanical and physical properties forming characteristics; and other information.
TO 1-1B-50, TECHNICAL MANUAL BASIC TECHNICAL ORDER FOR USAF AIRCRAFT WEIGHT AND BALANCE (8 AUG 2003)
TO 1-1B-50, TECHNICAL MANUAL BASIC TECHNICAL ORDER FOR USAF AIRCRAFT WEIGHT AND BALANCE (1 MAR 2005)., This manual outlines and defines the requirements, procedures, and responsibilities for weight and balance control of USAF aircraft. This manual also provides information and instructions for accomplishing the charts and forms that provide the means for continuous record and control of aircraft weight and balance. Information and explanation of principles, terms, and definitions are presented to provide weight and balance personnel with a general information manual pertinent to their particular function. The general requirements of this TO and the specific requirements of the -5 and -6 series TOs govern USAF aircraft weight and balance documentation and control.
Ident. Num:
TO 1-1B-50
Rev. Num:
-
TO 1-1B-50, TECHNICAL MANUAL BASIC TECHNICAL ORDER FOR USAF AIRCRAFT WEIGHT AND BALANCE (1 MAR 2005)., This manual outlines and defines the requirements, procedures, and responsibilities for weight and balance control of USAF aircraft. This manual also provides information and instructions for accomplishing the charts and forms that provide the means for continuous record and control of aircraft weight and balance. Information and explanation of principles, terms, and definitions are presented to provide weight and balance personnel with a general information manual pertinent to their particular function. The general requirements of this TO and the specific requirements of the -5 and -6 series TOs govern USAF aircraft weight and balance documentation and control.
TO 3B-1-1, TECHNICAL MANUAL NONDESTRUCTIVE INSPECTION METHODS, BASIC THEORY (15 JUN 2007)
TO 3B-1-1, TECHNICAL MANUAL NONDESTRUCTIVE INSPECTION METHODS, BASIC THEORY (15 JUN 2007) (NAVAIR 01-1A-16) (ARMY TM 1-1500-335-23)., This publication contains the concepts, process controls, and theory of Non Destructive Inspection (NDI) methods and SHALL be used as a guide in development of NDI procedures and manuals. Guidance for development of NDI procedures is contained in MIL-DTL- 87929C, Appendix F. NDI procedures SHALL be detailed step-by-step instructions with illustrations so a qualified NDI technician can perform the required inspection. In addition this manual provides guidance in safety guidelines of these NDI methods.
Ident. Num:
TO 3B-1-1
Rev. Num:
-
TO 3B-1-1, TECHNICAL MANUAL NONDESTRUCTIVE INSPECTION METHODS, BASIC THEORY (15 JUN 2007) (NAVAIR 01-1A-16) (ARMY TM 1-1500-335-23)., This publication contains the concepts, process controls, and theory of Non Destructive Inspection (NDI) methods and SHALL be used as a guide in development of NDI procedures and manuals. Guidance for development of NDI procedures is contained in MIL-DTL- 87929C, Appendix F. NDI procedures SHALL be detailed step-by-step instructions with illustrations so a qualified NDI technician can perform the required inspection. In addition this manual provides guidance in safety guidelines of these NDI methods.
