MIL-STD-1601 (SHIPS), MILITARY SPECIFICATION METHOD FOR 5/8 INCH DYNAMIC TEAR TESTING OF METALLIC MATERIALS. Military Standard MIL-STD-1601(SHIPS), dated 8 MAY 1973, is hereby canceled. These dynamic tear values should be determined using ASTM E 604, Standard Test Method for Dynamic Tear Testing of Metallic Materials.

MIL-STD-1602 (AS), MILITARY STANDARD PROGRESS REPORTS FOR RESEARCH AND DEVELOPMENT EQUIPMENT, REQUIREMENTS FOR. MIL-STD-1602 (AS) dated 8 June 1973, is hereby canceled. No Superseding Document.

MIL-STD-1604 (NOTICE 1), MILITARY STANDARD TECHNICAL AND MAINTENANCE OVERHAUL AND REPAIR STANDARDS, PREPARATION OF. Pending issuance of a Data Item Description (DID) relating to QATIPs, procurement of such data will be as prescribed in individual contracts.

MIL-STD-1604 (NOTICE 2), MILITARY STANDARD TECHNICAL AND MAINTENANCE OVERHAUL AND REPAIR STANDARDS, PREPARATION OF. THE FOLLOWING PAGES OF MIL-STD-1604 (OS) HAVE BEEN REVISED AND SUPERSEDE THE PAGES LISTED:

MIL-STD-1604 (NOTICE 3), MILITARY STANDARD TECHNICAL AND MAINTENANCE OVERHAUL AND REPAIR STANDARDS, PREPARATION OF. MIL-STD-1604, dated 28 September 1973, is hereby canceled. Future acquisitions should refer to MIL-M-24784/9, “Manual, Technical Repair Standards (TRS) Requirements for Ordnance Equipment”.

MIL-STD-1604 (OS), MILITARY STANDARD TECHNICAL AND MAINTENANCE OVERHAUL AND REPAIR STANDARDS, PREPARATION OF. The purpose of this standard is to delineate uniform requirements and criteria for the preparation of Technical and Maintenance Overhaul and Repair Standards (TRSs).

MIL-STD-1605 (SHIPS), MILITARY STANDARD PROCEDURES FOR CONDUCTING A SHIPBOARD ELECTROMAGNETIC INTERFERENCE (EMI) SURVEY (SURFACE SHIPS. This standard provides detailed procedures for conducting an electromagnetic interference (EMI) survey aboard surface ships. An EMI survey is required for new construction ships and ships receiving overhauls or other major repair work that changes the electromagnetic configuration.

MIL-STD-1606A (NOTICE 1), TECHNICAL REQUIREMENTS FOR AIR LAUNCHED GUIDED MISSILE PROPOSALS. MIL-STD-1606A, dated 7 September 1983, is hereby canceled without replacement.

MIL-STD-1606A, TECHNICAL REQUIREMENTS FOR AIR LAUNCHED GUIDED MISSILE PROPOSALS. This document, together with the REFERENCED DOCUMENTS listed in paragraph 3, delineates the general technical information requirements of NAVAIR (Naval Air Systems Command) for the preparation and submittal of proposals for design and construction, development (including related analyses, tests, and documentation), and delivery of Navy guided missiles.

MIL-STD-1607A (NOTICE 1), MILITARY STANDARD CHEMICAL CLEANING OF MAIN AND AUXILIARY BOILERS(SULFAMIC-CITRIC ACID METHOD. MIL-STD-1607A(SH), dated 11 August 1987, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1607A (NOTICE 2), MILITARY STANDARD CHEMICAL CLEANING OF MAIN AND AUXILIARY BOILERS(SULFAMIC-CITRIC ACID METHOD. MIL-STD-1607A, dated 22 January 1992, is inactive for new design and is no longer used, except for replacement purposes.

MIL-STD-1607A, MILITARY STANDARD CHEMICAL CLEANING OF MAIN AND AUXILIARY BOILERS (SULFAMIC-CITRIC ACID METHOD). This standard covers the requirements governing the procedure for chemical cleaning of main propulsion boilers of ferrous construction. Auxiliary (hotel load) boilers or waste heat boilers of ferrous or silicon-bronze (Herculay) construction can also be chemically cleaned using this standard Differences in the configuration and volume of auxiliary and waste hear boilers must be considered when this standard is used to clean non-propulsion boilers The procedure may be used by ship’s force, Naval shipyards, and private contractors

MIL-STD-1608C (NOTICE 1), MILITARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF COATS, WOMENS, DRESS. The following pages of MIL-STD-1608C have been revised and supersede the pages listed.

MIL-STD-1608C, MILITARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF COATS, WOMENS, DRESS. The scope of this standard is to provide standardized provisions for evaluating the quality of women's dress coats.

The purpose of this standard is to provide standardized provisions for evaluating the quality of women's dress, semi-dress, and utility skirts.

This standard covers the magnetic tape recorder configurations to be used to record and reproduce ASW sensor and system data.

MIL-STD-1611A (NOTICE 1), MILITARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF HOODS AND HAVELOCKS, WOMAN'S. Military Standard MIL-STD-1611A, dated 23 May 1978, has been reviewed and determined to be current.

MIL-STD-1611A PROVISIONS FOR EVALUATING QUALITY OF HOODS AND HAVELOCKS, WOMAN'S The purpose of this standard is to provide standardized provisions for evaluating the quality of woman's hoods and havelocks.

The scope of this standard is to provide standardized provisions for evaluating the quality of leather dress gloves.

MIL-STD-1614A (NOTICE 1), MILITARY STANDARD PROVISIONS FOR EVALUATING QUALITY OF CLOTH TYPE HOODS. Military Standard, MIL-STD-1614A, dated 19 December 1980, is hereby canceled without replacement.

The purpose of this standard is to provide standardized provisions for evaluating the quality of cloth type hoods.

MIL-STD-1621A, MILITARY STANDARD ACOUSTICAL AND VIBRATIONAL STANDARD REFERENCE QUANTITIES. This military standard is approved for use by the Commands of the Navy for measurement of levels of airborne, liquid-borne, and structure-borne noise.

MIL-STD-1622B (SH), DEPARTMENT OF DEFENSE STANDARD PRACTICE CLEANING OF SHIPBOARD COMPRESSED AIR SYSTEMS (17 FEB 1999)., This standard provides the requirements for cleaning of compressed air systems and components. Each activity should implement the applicable requirements of this document through a locally prepared and approved procedure. Activities subject to additional quality assurance requirements such as NAVSEA SS800-AG-MAN-010/P-9290 or NAVSEA SS521-AA-MAN-010 shall obtain procedure approval from the applicable certifying activity. This standard does not apply to reactor plant air systems.

MIL-STD-1623D (NOTICE 1), MILITARY STANDARD FIRE PERFORMANCE REQUIREMENTS AND APPROVED SPECIFICATIONS FOR INTERIOR FINISH MATERIALS AND FURNISHINGS(NAVAL SHIPBOARD USE) (3 JUL 1985)., The following pages of MIL-STD-1623D have been revised and supersede The pages listed:

MIL-STD-1623D(SH), DOD DESIGN CRITERIA STANDARD FIRE PERFORMANCE REQUIREMENTS AND APPROVED SPECIFICATIONS FOR INTERIOR FINISH MATERIALS AND FURNISHINGS (NAVAL SHIPBOARD USE) (7 DEC 1981)., The purpose of this standard is to establish fire performance criteria and provide a list of approved specifications for interior finish materials and furnishings to be used on Naval surface ships and submarines. Although the development of limits for toxic products of combustion is of major concern, the information generally available is not refined to the degree to allow inclusion of finite limits in this standard at this time.

MIL-STD-1623E(SH), DEPARTMENT OF DEFENSE DESIGN CRITERIA STANDARD, FIRE PERFORMANCE REQUIREMENTS AND APPROVED SPECIFICATIONS FOR INTERIOR FINISH MATERIALS AND FURNISHINGS (NAVAL SHIPBOARD USE) (20 JUN 2006)., This design criteria standard provides fire performance requirements and approved specifications for various categories of interior finish materials and furnishings for use on Naval surface ships and submarines.

MIL-STD-1624A (NOTICE 1), MILITARY STANDARD SHIP COMPARTMENT STANDARD NOMENCLATURE. MIL-STD-1624A, dated 10 August 1984, is hereby canceled and replaced by DOD-STD-2150, Ship Space Classification System

This standard provides a list of standard compartment names for use by designers, shipbuilders, and repair facilities involved in ship compartment definition.

MIL-STD-1625C (NOTICE 1), MILITARY STANDARD SAFETY CERTIFICATION PROGRAM FOR DRYDOCKING FACILITIES AND SHIPBUILDING WAYS FOR US NAVY SHIPS. To all holders of MIL-STD-1625C, the following pages of MIL-STD-1625C have been revised and supersede the pages listed.

The purpose of the SCP is to ensure the safety of U.S. Navy ships during docking and undocking operations and while in dock. It also relates to the safety of ships under construction and during launching operations. The capacity of the facility with regard to its foundations, a structure, and supporting military systems, including those for ship protection. Also included is an assessment of operating procedures, and personnel qualification procedures, and maintenance procedures supporting operational reliability.

MIL-STD-1627B, MILITARY STANDARD BENDING OF PIPE OR TUBE FOR SHIP PIPING SYSTEMS. This standard covers pipe bending, heat treatment, and inspection requirements and acceptance criteria for piping used for ships of the United States Navy.

MIL-STD-1627C (SH), MILITARY STANDARD BENDING OF PIPE OR TUBE FOR SHIP PIPING SYSTEMS. This standard covers pipe bending, heat treatment, and inspection requirements and acceptance criteria for piping used for ships of the United States Navy. NOTE: MIL-STD-1627 has been redesignated as a Design Criteria Standard. The cover page has been changed for Administrative reasons. There are no other changes to this Document.

MIL-STD-1628 (SHIPS), DEPARTMENT OF DEFENSE TEST METHOD FILLET WELD SIZE, STRENGTH, AND EFFICIENCY DETERMINATION (28 JUN 1974)., This standard contains the necessary data for selecting or calculating continuous double fillet weld sizes that will provide the required joint efficiency and yet be economical for the application involved.

MIL-STD-1629A (NOTICE 1), MILITARY STANDARD PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS, AND CRITICALITY ANALYSIS (7 JUN 1983)., The following pages of MIL-STD-1629A have been revised and supersede the pages listed:

MIL-STD-1629A (NOTICE 2), MILITARY STANDARD PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS, AND CRITICALITY ANALYSIS (28 NOV 1984)., The following pages of MIL-STD-1629A have been revised and supersede the pages listed:

MIL-STD-1629A (NOTICE 3), MILITARY STANDARD PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS, AND CRITICALITY ANALYSIS (4 AUGUST 1998)., MIL-STD-1629A, dated 24 November 1980, is hereby canceled. Users may consult various national and international documents for information regarding failure mode, effects, and criticality analysis.

MIL-STD-1629A, MILITARY STANDARD PROCEDURES FOR PERFORMING A FAILURE MODE, EFFECTS, AND CRITICALITY ANALYSIS (24 NOV 1980)., This standard establishes requirements and procedures for performing a failure mode, effects, and criticality analysis (FMECA) to systematically evaluate and document, by item failure mode analysis, the potential impact of each functional or hardware failure on mission success, personnel and system safety, system performance, maintainability, and maintenance requirements.

MIL-STD-1632A (NOTICE1), MILITARY STANDARD INSERT ARRANGEMENTS FOR MIL-C-28804 HIGH DENSITY, RECTANGULAR, ELECTRICAL CONNECTORS. MIL-STD-1632A, dated 27 March 1978, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1632A, INSERT ARRANGEMENTS FOR MIL-C-28804 HIGH DENSITY, RECTANGULAR, ELECTRICAL CONNECTORS. This standard covers insert arrangements for use with MIL-C-28804A high density rectangular Electric Connectors.

MIL-STD-1632A, MILITARY STANDARD INSERT ARRANGEMENTS FOR MIL-C-28804 HIGH DENSITY, RECTANGULAR, ELECTRICAL CONTACTS (27 MAR 1978). This Standard covers insert arrangements for use with MIL--28804A High Density Rectangular Electric Connectors.

MIL-STD-1635 (NOTICE 1), MILITARY STANDARD RELIABILITY GROWTH TESTING. MIL-STD-1635 (EC), dated 3 February 1978, is hereby canceled without replacement.

MIL-STD-1635 This standard covers the requirements and procedures for reliability development (Growth) tests. These tests are conducted during the hardware development phase on samples which have completed environmental tests prior to production commitment, and do not replace other tests described in the contract or equipment specification. These tests provide engineering information on the failure modes and mechanisms of a test under natural and induced environmental conditions of military operations. Reliability improvement (growth) will result when failure modes and mechanisms are discovered and identified and their recurrence prevented through implantation of corrective action.

MIL-STD-1636 (NOTICE 1), MILITARY STANDARD ADAPTERS, COAXIAL TO WAVEGUIDE SELECTION OF. MIL-STD-1636, DATED 22 April 1977, is hereby canceled without replacement.

MIL-STD-1636 This standard provides standard coaxial to waveguide adapters considered by the Department of Defense as standard for use in military equipment and application.

MIL-STD-1637A This standard provides standard waveguide, coaxial, and stripline dummy loads considered by the Department of Defense as standard for use in military equipment and applications.

MIL-STD-1637B (NOTICE 1), MILITARY STANDARD DUMMY LOADS, ELECTRICAL, WAVEGUIDE, COAXIAL, AND STRIPLINE, SELECTION OF. MIL-STD-1637B, dated 22 September 1989, is hereby canceled without replacement.

MIL-STD-1637B (NOTICE 1), MILITARY STANDARD DUMMY LOADS, ELECTRICAL, WAVEGUIDE, COAXIAL, AND STRIPLINE, SELECTION OF. MIL-STD-1637B, dated 22 September 1989, is hereby canceled without replacement.

MIL-STD-1637B This military standard provides standard waveguide, coaxial, and stripline dummy loads considered by the Department of Defense as standard for use in military equipment and applications.

MIL-STD-1638A (NOTICE 1), MILITARY STANDARD WAVEGUIDE ASSEMBLIES, RIGID AND FLEXIBLE, SELECTION OF. MIL-STD-1638A, dated 21 August 1980, has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1638A (NOTICE 2), MILITARY STANDARD WAVEGUIDE ASSEMBLIES, RIGID AND FLEXIBLE, SELECTION OF. MIL-STD-1638A, dated 21 August 1980, is hereby canceled without replacement.

This standard defines waveguide assemblies and considered by the Department of Defense as standard for use in military equipment and applications.

MIL-STD-1639A (NOTICE 1), MILITARY STANDARD POWER DIVIDERS, POWER COMBINERS, A ND POWER DIVIDER/COMBINERS, SELECTION OF. MIL-STD-1639A has been reviewed and determined to be valid for use in acquisition.

MIL-STD-1639A (NOTICE 2), MILITARY STANDARD POWER DIVIDERS, POWER COMBINERS, AND POWER DIVIDER/COMBINERS, SELECTION OF. MIL-STD-1639A, dated 22 February 1980, is hereby canceled without replacement.

MIL-STD-1639A This standard provides standard power diviers, power combiners, and powder divider/combiners considered by the Department of Defense as standard for use in military equipment and applications.

MIL-STD-1640 (NOTICE 1), MILITARY STANDARD MIXER STAGES, RADIO FREQUENCY, SELECTION OF. MIL-STD-1640B, dated 7 February 1985, is hereby canceled without replacement.

MIL-STD-1640B (NOTICE 1), MILITARY STANDARD MIXER STAGES, RADIO FREQUENCY, SELECTION OF. MIL-STD-1640B, dated 7 February 1985, is hereby canceled without replacement.

This standard provides a list of mixer stages for use in military equipment applications.

MIL-STD-1642 (NOTICE 1), MILITARY STANDARD DESIGN CRITERIA FOR PERSONNEL LOW PRESSURE CHAMBERS. MIL-STD-1642 , dated 20 August 1977, is hereby canceled without replacement.

MIL-STD-1642 (TD), MILITARY STANDARD DESIGN CRITERIA FOR PERSONNEL LOW PRESSURE CHAMBERS. This standard establishes general criteria for the development of personnel low pressure chambers.

MIL-STD-1646B (NOTICE 1), MILITARY STANDARD SERVICING TOOLS FOR ELECTRIC CONTACTS AND CONNECTIONS, SELECTION AND USE OF (13 SEP 1996)., MIL-STD-1646B, dated 29 July 1983, is hereby canceled without replacement.

MIL-STD-1646B, MILITARY STANDARD SERVICING TOOLS FOR ELECTRIC CONTACTS AND CONNECTIONS, SELECTION AND USE OF (23 JUL 1983)., This standard provides selected electrical contact crimping tools, turret heads, positioners, die sets, wire wrap tools, installing tools, removal tools, and grommet sealing plugs which are mandatory for use with all military electrical connectors and connections.

MIL-STD-1647D (NOTICE 2), MILITARY STANDARD IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS, BALL, ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS. TO ALL HOLDERS OF MIL-STD-1647D: 1. The following page of MIL-STD-1647D has been revised and supersedes the page listed:

MIL-STD-1647D (NOTICE 3), DEPARTMENT OF DEFENSE STANDARD PRACTICE IDENTIFICATION MARKINGS FOR DOMESTICALLY MANUFACTURED BEARINGS, BALL, ANNULAR FOR INSTRUMENTS AND PRECISION COMPONENTS. TO ALL HOLDERS OF MIL-STD-1647D: 1. THE FOLLOWING PAGE OF MIL-STD-1647D HAS BEEN REVISED AND SUPERSEDES THE PAGE LISTED:

This standard specifies the marking requirements for Identification and certification of miniature and Instrument type annular ball bearings of domestic manufacture.

MIL-STD-1647 This standard establishes the markings requirements for identification and certification of miniature and instrument type annular ball bearings of domestic manufacture.

MIL-STD-1648A (AS) (NOTICE 1), MILITARY STANDARD CRITERIA AND TEST PROCEDURES FOR ORDNANCE EXPOSED TO AN AIRCRAFT FUEL FIRE (10 MAR 1983) (SUPERSEDES MIL-STD-1648).

MIL-STD-1648A (AS) (NOTICE 2), MILITARY STANDARD CRITERIA AND TEST PROCEDURES FOR ORDNANCE EXPOSED TO AN AIRCRAFT FUEL FIRE (5 DEC 1995) (SUPERSEDES MIL-STD-1648)., MIL-STD-1648A, dated 30 SEP 1982, is hereby canceled without replacement.

MIL-STD-1648A (AS), MILITARY STANDARD CRITERIA AND TEST PROCEDURES FOR ORDNANCE EXPOSED TO AN AIRCRAFT FUEL FIRE (30 SEP 1982) (SUPERSEDES MIL-STD-1648)., This document establishes the minimum fast cook-off test requirements for air-launched weapons used aboard aircraft carriers and other air capable ships. This document specifies the criteria and and procedures to be used in demonstrating an acceptable level of cook-off safety of weapons when engulfed in an aircraft fuel fire.

MIL-STD-1649 (AS) (NOTICE 1), MILITARY STANDARD FILM, MOTION PICTURE, SUPER 8MM, LABORATORY PREPARATION OF. MIL-STD-1649 (AS), dated 31 May 1974, is hereby canceled without replacement.

MIL-STD-1649 (AS), MILITARY STANDARD FILM, MOTION PICTURE, SUPER 8MM, LABORATORY PREPARATION OF. This Standard establishes a standard laboratory practice for the preparation of Super 8mm motion picture projection film and its loading onto MS-14115 A,B,C, and D reels.

MIL-STD-1651 (NOTICE 1), MILITARY STANDARD INSERT ARRANGEMENTS FOR MIL-C-5015, MIL-C-22992 (CLASSES C, J, AND R), AND MIL-C-83723 (SERIES II) ELECTRICAL CONNECTORS (10 JUN 1976). To all holders of MIL-STD-1651, the following pages of MIL-STD-1651 have been revised and supersede the pages listed.

MIL-STD-1651 (NOTICE 2), MILITARY STANDARD INSERT ARRANGEMENTS FOR MIL-C-5015, MIL-C-22992 (CLASSES C, J, AND R), AND MIL-C-83723 (SERIES II) ELECTRICAL CONNECTORS (30 MAY 1979).

MIL-STD-1651 INSERT ARRANGEMENTS FOR MIL-C-5015, MIL-C-22992 (CLASSES C, J, AND R), AND MIL-c-83723 (SERIES II) ELECTRICAL CONNECTORS. This standard covers insert arrangements for use with MIL-C-5015, MIL-C-22992 (classes C, J, and R)), and MIL-C-35723 (series II) electrical connectors.

MIL-STD-1651A, MILITARY STANDARD INSERT ARRANGEMENTS FOR MIL-C-5015, MIL-C-22992 (CLASSES C, J, AND R), AND MIL-C-83723 (SERIES II) ELECTRICAL CONNECTORS (3 APR 1992)., This standard gives the dimensional requirements for insert arrangements used in MIL-C-5015, MIL-C-22992 (Classes C, J and R), and MIL-C-83723 (Series II) electrical connectors.

MIL-STD-1653B (AS) (NOTICE 1), DEPARTMENT OF DEFENSE INTERFACE STANDARD POWER CABLE ASSEMBLIES (4 MAY 1998)., MIL-STD-1653B, dated 30 May 1997, is hereby canceled without replacement.

MIL-STD-1653B (AS), DEPARTMENT OF DEFENSE INTERFACE STANDARD POWER CABLE ASSEMBLIES (30 MAY 1997)., This standard specifies the configuration requirements of input power cable assemblies for Oganizational (flightline) and Intermediate (shop) electronic test equipment, classified as Type I in MIL-T-28800, and rated up to 10 amperes. It also shows the relevant connections for the test equipment and power source receptacles.

MIL-STD-1655 (NOTICE 1), MILITARY STANDARD FITTINGS, FLARELESS, CLASSIFICATION OF DEFECTS OF. MIL-STD-1655, dated 10 April 1975, has been reviewed and determined to be current.

MIL-STD-1655 (NOTICE 2), MILITARY STANDARD FITTINGS, FLARELESS, CLASSIFICATION OF DEFECTS OF. MIL-STD-1655, dated 10 April 1975, is hereby cancelled. Future acquisition for this item should refer to MIL-HDBK-1655, “Classification of Defects of Flareless and Beam Seal Fittings.”

MIL-STD-1655, MILITARY STANDARD FITTINGS, FLARELESS, CLASSIFICATION OF DEFECTS OF (10 APR 1975) (S/S BY MIL-HDBK-1655)., This standard establishes a classification of commonly occurring defects applicable to the flareless fitting drawings specified in MIL-F-18280.

MIL-STD-1657A DEPARTMENT OF DEFENSE DESIGN CRITERIA SWITCHING EQUIPMENT, COMBAT SYSTEM, COMMAND AND CONTROL, FIRE CONTROL AND INTERIOR COMMUNICATION REQUIREMENTS FOR. This standard covers the requirements for the design of switching equipment used to control the interfaces and monitor the operation of equipment components of the combat system.

MIL-STD-1658 (NOTICE 1), MILITARY STANDARD SHIPBOARD GUIDED MISSILE LAUNCHING SYSTEM SAFETY REQUIREMENTS, MINIMUM. To all holders of MIL-STD-1658(OS): 1. Make the following pen and ink changes to MIL-STD-3658(OS) of 15 May 1974:

MIL-STD-1658 (NOTICE 2), MILITARY STANDARD SHIPBOARD GUIDED MISSILE LAUNCHING SYSTEM SAFETY REQUIREMENTS, MINIMUM. To all holders of MIl-STD-1658 (OS), add new paragraphs to the following pages.

MIL-STD-1658 (NOTICE 3), MILITARY STANDARD SHIPBOARD GUIDED MISSILE LAUNCHING SYSTEMM SAFETY REQUIREMENTS, MINIMUM. To all holders of MIL-STD-1658(OS): 1. Make the following pen and ink changes to MIL-S-1658(OS):

MIL-STD-1658 (OS) (NOTICE 4), DEPARTMENT OF DEFENSE DESIGN CRITERIA STANDARD SHIPBOARD GUIDED MISSILE LAUNCHING SYSTEM SAFETY REQUIREMENTS, MINIMUM (13 JUL 1999)., MIL-STD-1658, including Change Notice 3, dated 30 June 1982, is inactive for new design and is no longer used, except for replacement purposes.

MIL-STD-1658 (OS), DEPARTMENT OF DEFENSE DESIGN CRITERIA STANDARD SHIPBOARD GUIDED MISSILE LAUNCHING SYSTEM SAFETY REQUIREMENTS, MINIMUM (15 MAY 1974)., This standard establishes the minimum safety requirements for shipboard guided missile launching systems. Special requirements which may be imposed on launching systems handling missiles containing nuclear warheads or liquid fuels other than the hydrocarbon fuels are not included.

MIL-STD-1659, MILITARY SPECIFICATION, SEALING CONDITION OF AMMUNITION PRIMER TUBE FLASH HOLES (20 OCT 1976)., This standard depicts the preferred acceptable, and not acceptable sealing condition of ammunition primer tube flash holes.

MIL-STD-1660 (NOTICE 1) DESIGN CRITERIA FOR AMMUNITION UNIT LOADS Make pen and ink changes or add new paragraphs to the following pages.

MIL-STD-1660 (NOTICE 2) DESIGN CRITERIA FOR AMMUNITION UNIT LOADS MIL-STD-1660, dated 8 April 1977 and Notice 1, dated 6 June 1978, has been reviewed and determined to be valid for use in acquisition

MIL-STD-1660,MILITARY STANDARD DESIGN CRITERIA FOR AMMUNITION UNIT LOADS (8 APR 1977)., This standard establishes minimum design criteria and associated tests for ammunition unit loads.

MIL-STD-1661 This standard sets forth procedures for establishing and changing item names and designations of systems, equipments, and material items under the cognizance of the Naval Sea Systems Command and, when officially requested, systems, equipments, and material items under the cognizance of the Naval Air Systems Command. This standard defines the MARK and MOD system of nomenclature and gives instructions for processing requests for assignment of nomenclature.

MIL-STD-1662B This standard establishes the format, content, and general procedures for the preparation of ORDALT instructions. ORDALT instructions are prepared in either "short format" or "long format"

MIL-STD-1662C This standard establishes the format, content, and procedures for the preparation of ORDALT instructions. ORDALT instructions are prepared in either "short format" or "long format" (formerly, referred to as "short form" or "long form")

MIL-STD-1663 (NOTICE 1), MILITARY STANDARD LOADING RESTRAINT OF AMMUNITION AND EXPLOSIVES IN COMMERCIAL INTERMODAL CONTAINERS UTILIZING THE INTERNAL RESTRAINT SYSTEM KIT. MIL-STD-1663, HAS BEEN REVIEWED AND DETERMINED TO BE VALID FOR USE IN ACQUISITION.

MIL-STD-1663

MIL-STD-1664 (NOTICE 1) CONNECTIONS, ELECTRICAL CLIP TERMINATION MIL-STD-1664, dated 19 August 1981, is hereby canceled without replacement.

MIL-STD-1664A (NOTICE 1) CONNECTIONS, ELECTRICAL, CLIP TERMINATION MIL-STD-1665, dated 19 August 1981, is hereby canceled without replacement.

MIL-STD-1664 This standard establishes the requirements for producing a mechanically and electronically stable electrical clip termination made with a stranded or solid wire and appropriately designed terminal posts.

MIL-STD-1665 (NOTICE 1) TEST EQUIPMENT FOR THE STANDARD ELECTRONIC MODULES PROGRAM The following pages of MIL-STD-1665 have been revised and supersede the pages listed.

MIL-STD-1665 (NOTICE 2) TEST EQUIPMENT FOR THE STANDARD ELECTRONIC MODULES PROGRAM The following pages of MIL-STD-1665 have been revised and supersede the pages listed.

MIL-STD-1665 (NOTICE 3) TEST EQUIPMENT FOR THE STANDARD ELECTRONIC MODULES PROGRAM The following pages of MIL-STD-1665 have been revised and supersede the pages listed.

MIL-STD-1665 (NOTICE 4) TEST EQUIPMENT FOR THE STANDARD ELECTRONIC MODULES PROGRAM The following pages of MIL-STD-1665 have been revised and supersede the pages listed.

MIL-STD-1665 (NOTICE 5) TEST EQUIPMENT FOR THE STANDARD ELECTRONIC MODULES PROGRAM The following pages of MIL-STD-1665 are new or have been revised and supersede the pages listed.

MIL-STD-1665 (NOTICE 6) TEST EQUIPMENT FOR THE STANDARD ELECTRONIC MODULES PROGRAM. The following pages of MIL-STD-1665 are new or have been revised and supersede the pages listed.

MIL-STD-1665 (NOTICE 7) TEST EQUIPMENT FOR THE STANDARD ELECTRONIC MODULES PROGRAM MIL-STD-1665, dated 20 January 1978, is hereby canceled without replacement.