EverySpec Logo
Your free source for specifications, standards, and handbooks

MIL SPECS (MIL-DTL)

MIL-DTL-0070446B (w/AMENDMENT 1), DETAIL SPECIFICATION MACHINE GUN, 5.56MM: M249 (14 JUN 2007)
Ident. Num:
MIL-DTL-0070446 
  Rev. Num:

MIL-DTL-0070446B (w/AMENDMENT 1), DETAIL SPECIFICATION MACHINE GUN, 5.56MM: M249 (14 JUN 2007)., This specification is approved for interim use by the U.S. Army Armaments Research, Development and Engineering Center (ARDEC). Other activities in the Department of Defense may use this interim revision or may continue using MIL-M-70446A. This specification prescribes the detail requirements and identifies the verification procedures for the Machine Gun, 5.56MM: M249, hereafter referred to simply as the M249.
MIL-DTL-11015/18E, MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), STYLE CK05 (14 May 2001) [SUPERSEDING MIL-C-
Ident. Num:
MIL-DTL-11015 
  Rev. Num:

MIL-DTL-11015/18E, MILITARY SPECIFICATION SHEET CAPACITORS, FIXED, CERAMIC DIELECTRIC (GENERAL PURPOSE), STYLE CK05 (14 May 2001) [SUPERSEDING MIL-C-11015/18D]., The requirements for acquiring the capacitors described herein shall consist of this specification and MIL-C-11015. This specification is approved for use by all Departments and Agencies of the Department of Defense. INACTIVE FOR NEW DESIGN after 28 September 1970.
MIL-DTL-117H, DETAIL SPECIFICATION, BAGS, HEAT-SEALABLE (30 APR 2001)
Ident. Num:
MIL-DTL-117 
  Rev. Num:

MIL-DTL-117H, DETAIL SPECIFICATION, BAGS, HEAT-SEALABLE (30 APR 2001). This document covers heat-sealable bags used in military preservation.
MIL-DTL-1222J, DETAIL SPECIFICATION STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR (8 DEC 2000) [SUPERCEDING MIL-S-1222H]
Ident. Num:
MIL-DTL-1222 
  Rev. Num:

MIL-DTL-1222J, DETAIL SPECIFICATION STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR (8 DEC 2000) [SUPERSEDING MIL-S-1222H]., This specification is approved for use by all Departments and Agencies of the Department of Defense. 1 SCOPE 1.1 Scope. This specification covers standard studs, hex cap screws, and heavy hex bolts in nominal standard diameters of ¼ inch to 4 inches, nuts in nominal standard diameters of ¼ inch to 3 inches, and socket head cap screws in nominal standard diameters of ¼ inch to 1½ inches for submarine safety and other applications where a high degree of reliability is required (see 6.1).
MIL-DTL-12883/54, Sockets, Plug-In Electronic Components Socket for MIL-PRF 6106 Relays and MS27742 Relays
Ident. Num:
MIL-DTL-12883/54  
  Rev. Num:

INCH-POUND MIL-DTL-12883/54A 18 February 2003 SUPERSEDING MIL-PRF-12883/54 24 January 1996 DETAIL SPECIFICATION SHEET SOCKETS, PLUG-IN ELECTRONIC COMPONENTS SOCKET FOR MIL-PRF 6106 RELAYS AND MS27742 RELAYS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-12883.
MIL-DTL-13486E, DETAIL SPECIFICATION CABLES, SPECIAL PURPOSE, ELECTRICAL: LOW-TENSION, HEAVY-DUTY, SINGLE CONDUCTOR AND MULTIPLE CONDUCTOR, SHIELDED A
Ident. Num:
MIL-DTL-13486 
  Rev. Num:

MIL-DTL-13486E, DETAIL SPECIFICATION CABLES, SPECIAL PURPOSE, ELECTRICAL: LOW-TENSION, HEAVY-DUTY, SINGLE CONDUCTOR AND MULTIPLE CONDUCTOR, SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (8 MAY 2006)., This specification covers two types (shielded and unshielded) of insulated, heavy-duty, single and multiconductor, electrical cables for use in low-tension circuits (see 6.1).
MIL-DTL-13924D (NOTICE 1), DETAIL SPECIFICATION COATING, OXIDE, BLACK, FOR FERROUS METALS
Ident. Num:
MIL-DTL-13924 
  Rev. Num:

MIL-DTL-13924D (NOTICE 1), DETAIL SPECIFICATION COATING, OXIDE, BLACK, FOR FERROUS METALS.MIL-DTL-13924D, dated 18 March 1999, has been reviewed and determined to be valid for use in acquisition
MIL-DTL-13924D, DETAILED SPECIFICATION COATING, OXIDE, BLACK, FOR FERROUS METALS (18 MAR 1999) [SUPERSEDING MIL-C-13924C]
Ident. Num:
MIL-DTL-13924 
  Rev. Num:

MIL-DTL-13924D, DETAILED SPECIFICATION COATING, OXIDE, BLACK, FOR FERROUS METALS (18 MAR 1999) [SUPERSEDING MIL-C-13924C]., This specification covers black oxide coatings applied to ferrous metals (wrought iron, carbon, low alloy, and corrosion resistant steels). Black oxide coatings, with or without a supplementary preservative treatment, may be used where a black surface is required. Only very limited corrosion protection, under mildly corrosive conditions, is obtained as a result of black oxide coating.
MIL-DTL-14072E (CR), DETAIL SPECIFICATION FINISHES FOR GROUND BASED ELECTRONIC EQUIPMENT (31 MAY 2007) (SUPERSEDING MIL-F-14072D)
Ident. Num:
MIL-DTL-14072 
  Rev. Num:

MIL-DTL-14072E (CR), DETAIL SPECIFICATION FINISHES FOR GROUND BASED ELECTRONIC EQUIPMENT (31 MAY 2007) (SUPERSEDING MIL-F-14072D)., This specification covers requirements for finishes necessary to protect ground electronic equipment from the deteriorating effects of climatic conditions encountered in military use.
MIL-DTL-14538D, DETAIL SPECIFICATION CHROMIUM PLATING, BLACK (ELECTRODEPOSITED) (16 JUN 1999)
Ident. Num:
MIL-DTL-14538 
  Rev. Num:

MIL-DTL-14538D, DETAIL SPECIFICATION CHROMIUM PLATING, BLACK (ELECTRODEPOSITED) (16 JUN 1999)., This specification covers an electrodeposited black chromium finish. It is generally applied to steels but may be used as a plating for other metals such as brass, copper, iron and chromium (see 6.1, 6.3 and 6.4).
MIL-DTL-15024F, DETAIL SPECIFICATION PLATES, TAGS, AND BANDS FOR IDENTIFICATION OF EQUIPMENT, GENERAL SPECIFICATION FOR (28 NOV 1997) (SUPERSEDING MIL
Ident. Num:
MIL-DTL-15024 
  Rev. Num:

MIL-DTL-15024F, DETAIL SPECIFICATION PLATES, TAGS, AND BANDS FOR IDENTIFICATION OF EQUIPMENT, GENERAL SPECIFICATION FOR (28 NOV 1997) (SUPERSEDING MIL-P-1502E)., This performance specification covers the physical characteristics of plates, tags and bands (identification devices) used for identification of equipment. Examples of information to be marked on the identification devices are covered in the applicable specification sheets.
MIL-DTL-15562G, DETAIL SPECIFICATION, MATTING OR SHEET, FLOOR COVERING, INSULATING FOR HIGH VOLTAGE APPLICATION (31 MAY 1996) (SUPERSEDING MIL-M-15562
Ident. Num:
MIL-DTL-15562 
  Rev. Num:

MIL-DTL-15562G, DETAIL SPECIFICATION, MATTING OR SHEET, FLOOR COVERING, INSULATING FOR HIGH VOLTAGE APPLICATION (31 MAY 1996) (SUPERSEDING MIL-M-15562F)., This specification covers rubber or plastic matting and sheet floor coverings for use around electrical apparatus or circuits, as a safety measure to protect personnel from accidental exposure to electrical potentials not exceeding 3000 volts. Equipment operating at higher voltages utilize other built-in safety measures to provide personnel protection.
MIL-DTL-15659J (SUPPLEMENT 1), DETAIL SPECIFICATION TERMINAL, LUG: SOLDER, COPPER AND PHOSPHOR BRONZE (15 DEC 2003) [SUPERSEDING MIL-T-15659H)
Ident. Num:
MIL-DTL-15659 
  Rev. Num:

MIL-DTL-15659J (SUPPLEMENT 1), DETAIL SPECIFICATION TERMINAL, LUG: SOLDER, COPPER AND PHOSPHOR BRONZE (15 DEC 2003) [SUPERSEDING MIL-T-15659H).
MIL-DTL-15659J, DETAIL SPECIFICATION TERMINAL, LUG: SOLDER, COPPER AND PHOSPHOR BRONZE (15 DEC 2003) [SUPERSEDING MIL-T-15659H)
Ident. Num:
MIL-DTL-15659 
  Rev. Num:

MIL-DTL-15659J, DETAIL SPECIFICATION TERMINAL, LUG: SOLDER, COPPER AND PHOSPHOR BRONZE (15 DEC 2003) [SUPERSEDING MIL-T-15659H)., This specification covers copper and phosphor bronze or tin brass strip solder electrical lug terminals.
MIL-DTL-16232G, DETAIL SPECIFICATION PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (7 JAN 2000)
Ident. Num:
MIL-DTL-16232 
  Rev. Num:

MIL-DTL-16232G, DETAIL SPECIFICATION PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (7 JAN 2000)., This specification covers two types of heavy phosphate coating for ferrous metals, applied by immersion. The coatings consist of a manganese phosphate or zinc phosphate base and, when specified, a supplementary treatment (see 6.1).
MIL-DTL-16232G, DETAIL SPECIFICATION PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (7 JAN 2000) [SUPERSEDING DOD-P-16232F AND MIL-P-16232E]
Ident. Num:
MIL-DTL-16232 
  Rev. Num:

MIL-DTL-16232G, DETAIL SPECIFICATION PHOSPHATE COATING, HEAVY, MANGANESE OR ZINC BASE (7 JAN 2000) [SUPERSEDING DOD-P-16232F AND MIL-P-16232E]., This specification covers two types of heavy phosphate coating for ferrous metals, applied by immersion. The coatings consist of a manganese phosphate or zinc phosphate base and, when specified, a supplementary treatment (see 6.1).
MIL-DTL-16377H (SH) (SUPPLEMENT 1), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 199
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SH) (SUPPLEMENT 1), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 1996). This supplement forms a part of Military Specification MIL-DTL-16377H(SH), dated 2 August 1996.
MIL-DTL-16377H (SH) (SUPPLEMENT 1A), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SH) (SUPPLEMENT 1A), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2004) [SUPERSEDING SUPPLEMENT 1]., This supplement forms a part of MIL-DTL-16377H(SH), dated 2 August 1996.
MIL-DTL-16377H (SH) (SUPPLEMENT 1B), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H (SH) (SUPPLEMENT 1B), DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (27 SEP 2005) [SUPERSEDING SUPPLEMENT 1B]., This supplement forms a part of MIL-DTL-16377H(SH), dated 2 August 1996.
MIL-DTL-16377H, DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 1996) [SUPERSEDING MIL-
Ident. Num:
MIL-DTL-16377 
  Rev. Num:

MIL-DTL-16377H, DETAIL SPECIFICATION FIXTURES, LIGHTING; AND ASSOCIATED PARTS; SHIPBOARD USE, GENERAL SPECIFICATION FOR (2 AUG 1996) [SUPERSEDING MIL-F-16377G (SH)]., This specification covers fluorescent and incandescent lighting fixtures (lights) and associated parts. used for detail and general illumination on Naval ships and boats.
MIL-DTL-17H (SUPPLEMENT 1), DETAIL SPECIFICATION CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERAL SPECIFCATION FOR
Ident. Num:
MIL-DTL-17 
  Rev. Num:

MIL-DTL-17H (SUPPLEMENT 1), DETAIL SPECIFICATION CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERAL SPECIFCATION FOR., This supplement forms a part of MIL-DTL-17H, dated 19 August 2005.
MIL-DTL-17H, DETAIL SPECIFICATION, CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERATION SPECIFICATION FOR (4 AUG 2006)
Ident. Num:
MIL-DTL-17 
  Rev. Num:

MIL-DTL-17H, DETAIL SPECIFICATION, CABLES, RADIO FREQUENCY, FLEXIBLE AND SEMIRIGID, GENERATION SPECIFICATION FOR (4 AUG 2006)., This supplement forms a part of MIL-DTL-17H, dated 19 August 2005.
MIL-DTL-18240F (AMENDMENT 1), DETAIL SPECIFICATION FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250°F MAXIMUM (13 MAR 2000) [SUPERSEDING MIL-F-1
Ident. Num:
MIL-DTL-18240 
  Rev. Num:

MIL-DTL-18240F (AMENDMENT 1), DETAIL SPECIFICATION FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250°F MAXIMUM (13 MAR 2000) [SUPERSEDING MIL-F-18240E).
MIL-DTL-18240F, DETAIL SPECIFICATION FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250°F MAXIMUM (2 JUN 1997) [SUPERSEDING MIL-F-18240E)
Ident. Num:
MIL-DTL-18240 
  Rev. Num:

MIL-DTL-18240F, DETAIL SPECIFICATION FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250°F MAXIMUM (2 JUN 1997) [SUPERSEDING MIL-F-18240E)., This specification defines the requirements for self-locking elements for use in externally threaded fasteners such as bolts and screws to be used in fasteners with either UNC, UNJC, UNF, UNJF, UNRC or UNRF threads and where the temperatures will not exceed 250°F.
MIL-DTL-19491H, DETAIL SPECIFICATION SEMICONDUCTOR DEVICES, PACKAGING OF (28 JUN 2002)
Ident. Num:
MIL-DTL-19491 
  Rev. Num:

MIL-DTL-19491H, DETAIL SPECIFICATION SEMICONDUCTOR DEVICES, PACKAGING OF (28 JUN 2002)., This specification covers the requirements for the preservation, packing, and container marking of semiconductor devices such as transistors and diodes (FSC 5961) (see 6.1).
MIL-DTL-197K (w/ AMENDMENT 1), DETAIL SPECIFICATION PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES (11 OCT 2005)
Ident. Num:
MIL-DTL-197 
  Rev. Num:

MIL-DTL-197K (w/ AMENDMENT 1), DETAIL SPECIFICATION PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES (11 OCT 2005)., This specification covers the cleaning, drying, preservation, packaging, and packaging marking requirements for all types and sizes of stock and production bearings, associated parts, and subassemblies (see 6.1).
MIL-DTL-197K (W/ AMENDMENT 1)., DETAIL SPECIFICATION PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES (11 OCT 2005)
Ident. Num:
MIL-DTL-197 
  Rev. Num:

MIL-DTL-197K (W/ AMENDMENT 1)., DETAIL SPECIFICATION PACKAGING OF BEARINGS, ASSOCIATED PARTS AND SUBASSEMBLIES (11 OCT 2005)., This specification covers the cleaning, drying, preservation, packaging, and packaging marking requirements for all types and sizes of stock and production bearings, associated parts, and subassemblies (see 6.1).
MIL-DTL-19834C, DETAIL SPECIFICATION PLATES, IDENTIFICATION OR INSTRUCTION, METAL FOIL, ADHESIVE BACKED GENERAL SPECIFICATION FOR (6 JUL 2006) (SUPERS
Ident. Num:
MIL-DTL-19834 
  Rev. Num:

MIL-DTL-19834C, DETAIL SPECIFICATION PLATES, IDENTIFICATION OR INSTRUCTION, METAL FOIL, ADHESIVE BACKED GENERAL SPECIFICATION FOR (6 JUL 2006) (SUPERSEDING MIL-P-19834B). This specification covers adhesive-backed metal foil identification or instruction plates, herein referred to as identification plates, for use as internal and external equipment identification or instruction (see 6.1).
MIL-DTL-22342E, DETAIL SPECIFICATION BROWS, ALUMINUM, BEAM AND TRUSS (7 JUL 1995) [SUPERSEDING MIL-B-22342D]
Ident. Num:
MIL-DTL-22342 
  Rev. Num:

MIL-DTL-22342E, DETAIL SPECIFICATION BROWS, ALUMINUM, BEAM AND TRUSS (7 JUL 1995) [SUPERSEDING MIL-B-22342D]., This specification covers aluminum beam and truss brows (ship's gangplanks).
MIL-DTL-22520G (SUPPLEMENT 1), DETAIL SPECIFICATION CRIMPING TOOLS, WIRE TERMINATION, GENERAL SPECIFICATION FOR (12 SEP 1997) [SUPERSEDING MIL-C-22520F]
Ident. Num:
MIL-DTL-22520 
  Rev. Num:

MIL-DTL-22520G (SUPPLEMENT 1), DETAIL SPECIFICATION CRIMPING TOOLS, WIRE TERMINATION, GENERAL SPECIFICATION FOR (12 SEP 1997) [SUPERSEDING MIL-C-22520F].
MIL-DTL-22520G, DETAIL SPECIFICATION CRIMPING TOOLS, WIRE TERMINATION, GENERAL SPECIFICATION FOR (12 SEP 1997) [SUPERSEDING MIL-C-22520F]
Ident. Num:
MIL-DTL-22520 
  Rev. Num:

MIL-DTL-22520G, DETAIL SPECIFICATION CRIMPING TOOLS, WIRE TERMINATION, GENERAL SPECIFICATION FOR (12 SEP 1997) [SUPERSEDING MIL-C-22520F]., This specification covers the general requirements for crimping tools, accessories and inspection gages used for connecting removable contacts (such as; signal, power, coaxial, shielded, thermocouple, and filter pin contacts) coaxial connectors, shielded connectors, ferrules, terminals, end caps and splices to wire conductors for use in electric connectors, terminal junction systems, and other electric or electronic components. The crimping tools and accessories covered by this specification are for use by the military and are the only connector assembly devices to be qualified, procured and issued for military maintenance use.
MIL-DTL-22992F (w/ AMENDMENT 1), DETAIL SPECIFICATION CONNECTORS, PLUGS AND RECEPTACLES, ELECTRICAL, WATERPROOF, QUICK DISCONNECT, HEAVY DUTY TYPE, GENERAL SPECIFICATION FOR (25 SEP 2006)
Ident. Num:
MIL-DTL-22992 
  Rev. Num:

MIL-DTL-22992F (w/ AMENDMENT 1), DETAIL SPECIFICATION CONNECTORS, PLUGS AND RECEPTACLES, ELECTRICAL, WATERPROOF, QUICK DISCONNECT, HEAVY DUTY TYPE, GENERAL SPECIFICATION FOR (25 SEP 2006)., This specification covers multi-contact, heavy duty, quick disconnect, waterproof, electrical plug and receptacle connectors and associated accessories for electronic and electrical power and control circuits. Connectors are rated for -55°C to +125°C (see 6.1).
MIL-DTL-23549D, DETAIL SPECIFICATION, GREASE, GENERAL PURPOSE (10 MAY 2002) [SUPERSEDING MIL-G-23549C]
Ident. Num:
MIL-DTL-23549 
  Rev. Num:

MIL-DTL-23549D, DETAIL SPECIFICATION, GREASE, GENERAL PURPOSE (10 MAY 2002) [SUPERSEDING MIL-G-23549C]., This specification covers the requirements for one type and grade of a general purpose molybdenum disulfide grease for extended use at temperatures up to 177 °C (350 °F) and for brief periods of use at temperatures up to 204 °C (400 °F) (see 6.1).
MIL-DTL-24308F, DETAIL SPECIFICATION CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL, RACK AND PANEL, GENERAL SPECIFIC
Ident. Num:
MIL-DTL-24308 
  Rev. Num:

MIL-DTL-24308F, DETAIL SPECIFICATION CONNECTORS, ELECTRIC, RECTANGULAR, NONENVIRONMENTAL, MINIATURE, POLARIZED SHELL, RACK AND PANEL, GENERAL SPECIFICATION FOR (25 JUN 2007)., This specification covers the requirements for nonenvironmental, polarized shell, miniature, rack and panel connectors having pin and socket, crimp (removable), solder (nonremovable), or insulation displacement (nonremovable) contacts with rigid or float mounting, designed for -55°C to +125°C operating temperature range.
MIL-DTL-24784/22, DETAIL SPECIFICATION SHEET TECHNICAL CONTENT DEVELOPMENT REQUIREMENTS FOR COMBAT SYSTEM TECHNICAL OPERATIONS MANUALS (CSTOMS); HULL,
Ident. Num:
MIL-DTL-24784 
  Rev. Num:

MIL-DTL-24784/22, DETAIL SPECIFICATION SHEET TECHNICAL CONTENT DEVELOPMENT REQUIREMENTS FOR COMBAT SYSTEM TECHNICAL OPERATIONS MANUALS (CSTOMS); HULL, MECHANICAL, AND ELECTRICAL (HM&E) SYSTEM AND EQUIPMENT MANUALS; ELECTRONIC [INCLUDING SERVICE TEST ELECTRONIC, EXPERIMENTAL ELECTRONIC AND INTERIOR COMMUNICATION (IC)] SYSTEM AND EQUIPMENT MANUALS; AND WEAPON SYSTEMS AND WEAPON EQUIPMENT MANUALS (3 NOV 2007)., This specification sets forth content requirements for the preparation of technical manuals (TMs) covering description, operation, maintenance, installation, and parts support for Combat System Technical Operations Manuals (CSTOMs); Hull, Mechanical, and Electrical (HM&E) Systems and Equipment Manuals; Electronic [including Service Test Electronic, Experimental Electronic, and Interior Communications (IC)] System and Equipment Manuals; and Weapon Systems and Weapon Equipment Manuals. The requirements are applicable for the output of paper or for the display of page-oriented, linear, and non-linear TMs on an Electronic Display System (EDS).
MIL-DTL-24784C (NAVY) (SUPPLEMENT 1), DETAIL SPECIFICATION MANUALS, TECHNICAL: GENERAL ACQUISITION AND DEVELOPMENT REQUIREMENTS, GENERAL SPECIFICATIO
Ident. Num:
MIL-DTL-24784 
  Rev. Num:

MIL-DTL-24784C (NAVY) (SUPPLEMENT 1), DETAIL SPECIFICATION MANUALS, TECHNICAL: GENERAL ACQUISITION AND DEVELOPMENT REQUIREMENTS, GENERAL SPECIFICATION FOR (3 NOV 2007). This supplement forms a part of MIL-DTL-24784C(NAVY) dated 3 November 2007.
MIL-DTL-24784C (NAVY), DETAIL SPECIFICATION MANUALS, TECHNICAL: GENERAL ACQUISITION AND DEVELOPMENT REQUIREMENTS, GENERAL SPECIFICATION FOR (3 NOV 20
Ident. Num:
MIL-DTL-24784 
  Rev. Num:

MIL-DTL-24784C (NAVY), DETAIL SPECIFICATION MANUALS, TECHNICAL: GENERAL ACQUISITION AND DEVELOPMENT REQUIREMENTS, GENERAL SPECIFICATION FOR (3 NOV 2007)., This specification establishes the general acquisition and development requirements needed to prepare digital technical information for multi-output presentation of NAVSEA Technical Manuals (TMs) (see 6.4.21). The technical content and style and format requirements contained in this specification can be used to develop and assemble complete TMs for ships, shipboard systems (see 6.4.20), and equipment. The requirements apply to the output of paper TMs or, to the display of page-oriented linear and non-linear Interactive Electronic Technical Manuals (IETMs) (see 6.4.10) on an Electronic Display System (EDS).
MIL-DTL-25579F, MILITARY SPECIFICATION HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, HIGH TEMPERATURE, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR (10 JUL 20
Ident. Num:
MIL-DTL-25579 
  Rev. Num:

MIL-DTL-25579F, MILITARY SPECIFICATION HOSE ASSEMBLY, POLYTETRAFLUOROETHYLENE, HIGH TEMPERATURE, MEDIUM PRESSURE, GENERAL SPECIFICATION FOR (10 JUL 2006)., This specification contains the requirements for medium pressure, high temperature, polytetrafluoroethylene (PTFE) hose assemblies, reinforced with a corrosion-resistant steel (CRES) wire braid for use in fuel, lubricating oil, water-alcohol, hydraulics and pneumatic systems within the limits specified herein.
MIL-DTL-25708D (AMENDMENT 1), DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (1 OCT 2001) [SUPERSEDING MIL-A-25708C]
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708D (AMENDMENT 1), DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (1 OCT 2001) [SUPERSEDING MIL-A-25708C]., This amendment forms a part of MIL-DTL-25708D, dated 23 July 1999, and is approved for use by all Departments and Agencies of the Department of Defense.
MIL-DTL-25708D, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (23 JUL 1999) [SUPERSEDING mil-a-25708C]
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708D, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (23 JUL 1999) [SUPERSEDING MIL-A-25708C]., This document covers the general requirements (for externally mounted) blade type L-band antennas (see 6.1).
MIL-DTL-25708E, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (2 OCT 2006) [SUPERSEDING MIL-DTL-25708D AND MIL-A-25708C]
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708E, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (2 OCT 2006) [SUPERSEDING MIL-DTL-25708D AND MIL-A-25708C]., This document covers the general requirements (for externally mounted) blade type L-band antennas (see 6.1).
MIL-DTL-25708F, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (28 MAY 2008)
Ident. Num:
MIL-DTL-25708 
  Rev. Num:

MIL-DTL-25708F, DETAIL SPECIFICATION ANTENNAS, BLADE, L-BAND, GENERAL SPECIFICATION FOR (28 MAY 2008)., This document covers the general requirements (for externally mounted) blade type L-band antennas (see 6.1).
MIL-DTL-26074F (NOTICE 1), DETAIL SPECIFICATION COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR
Ident. Num:
MIL-DTL-26074 
  Rev. Num:

MIL-DTL-26074F (NOTICE 1), DETAIL SPECIFICATION COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR. MIL-DTL-26074F is hereby cancelled. Previous users for Naval Nuclear Propulsion Program applications only should refer to MIL-DTL-32119. Previous users of MIL-C- 26074E should refer to SAE AMS-C-26074. If copies of MIL-DTL-26074F are needed for historical purposes, contact NAVSEA 05Q, 1333 Isaac Hull Avenue SE, STOP 5160, Washington Navy Yard, DC 20376-5160.
MIL-DTL-26074F, DETAIL SPECIFICATION COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR
Ident. Num:
MIL-DTL-26074 
  Rev. Num:

MIL-DTL-26074F, DETAIL SPECIFICATION COATINGS, ELECTROLESS NICKEL, REQUIREMENTS FOR. MIL-DTL-26074F is a controlled distribution document. If copies of MIL-DTL-26074F are needed for historical purposes, contact NAVSEA 05Q, 1333 Isaac Hull Avenue SE, Stop 5160, Washington Navy Yard, DC 20376-5160.
MIL-DTL-26482H (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, (CIRCULAR, MINIATURE, QUICK DISCONNECT, ENVIRONMENT RESISTING), RECEPTACLES AND PLUGS, GENERAL SPECIFICATION FOR (20 FEB 2007) [SUPERSEDING MIL-C-26482G]
Ident. Num:
MIL-DTL-26482 
  Rev. Num:

MIL-DTL-26482H (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, (CIRCULAR, MINIATURE, QUICK DISCONNECT, ENVIRONMENT RESISTING), RECEPTACLES AND PLUGS, GENERAL SPECIFICATION FOR (20 FEB 2007) [SUPERSEDING MIL-C-26482G]., This supplement forms a part of MIL-DTL-26482H, dated 20 February 2007.
MIL-DTL-26482H, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, (CIRCULAR, MINIATURE, QUICK DISCONNECT, ENVIRONMENT RESISTING), RECEPTACLES AND PLUGS, GENERAL SPECIFICATION FOR (20 FEB 2007) [SUPERSEDING MIL-C-26482G]
Ident. Num:
MIL-DTL-26482 
  Rev. Num:

MIL-DTL-26482H, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, (CIRCULAR, MINIATURE, QUICK DISCONNECT, ENVIRONMENT RESISTING), RECEPTACLES AND PLUGS, GENERAL SPECIFICATION FOR (20 FEB 2007) [SUPERSEDING MIL-C-26482G]., This specification covers the general requirements for two series of environment resisting, quick disconnect, miniature, circular electrical connectors (and accessories). Each series contains hermetic receptacles. The two series of connectors are intermateable when using power contacts and are not intermateable when using shielded contacts. When intermated, the minimum performance requirement for series 1 connectors will be met.
MIL-DTL-26500F (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, GENERAL PURPOSE, ELECTRICAL, MINIATURE, CIRCULAR, ENVIRONMENT RESISTING, GENERAL SPECI
Ident. Num:
MIL-DTL-26500 
  Rev. Num:

MIL-DTL-26500F (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, GENERAL PURPOSE, ELECTRICAL, MINIATURE, CIRCULAR, ENVIRONMENT RESISTING, GENERAL SPECIFICATION FOR (6 FEB 2004)., This supplement forms a part of MIL-DTL-26500F, dated 6 February 2004.
MIL-DTL-26500F, DETAIL SPECIFICATION CONNECTORS, GENERAL PURPOSE, ELECTRICAL, MINIATURE, CIRCULAR, ENVIRONMENT RESISTING, GENERAL SPECIFICATION FOR 6
Ident. Num:
MIL-DTL-26500 
  Rev. Num:

MIL-DTL-26500F, DETAIL SPECIFICATION CONNECTORS, GENERAL PURPOSE, ELECTRICAL, MINIATURE, CIRCULAR, ENVIRONMENT RESISTING, GENERAL SPECIFICATION FOR (6 FEB 2004)., This specification covers an environment-resisting family of miniature, circular, electrical connectors (plugs and receptacles), designed to meet the requirements of aerospace vehicles.
MIL-DTL-27443F (USAF), DETAILED SPECIFICATION PALLETS, CARGO, AIRCRAFT, TYPE HCU-6/E AND HCU-12/E (15 JUL 2003
Ident. Num:
MIL-DTL-27443 
  Rev. Num:

MIL-DTL-27443F (USAF), DETAILED SPECIFICATION PALLETS, CARGO, AIRCRAFT, TYPE HCU-6/E AND HCU-12/E (15 JUL 2003)., Pallets, cargo, aircraft, covered by this specification have a capacity of 10,000 pounds and 5,000 pounds.
MIL-DTL-27500H (AMENDMENT 1), MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (26 NOV 1999) (SUPERSEDING MIL-C-27500G)
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H (AMENDMENT 1), MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (26 NOV 1999) (SUPERSEDING MIL-C-27500G)., This amendment forms a part of MIL-DTL-27500H, dated 10 December 1997, and is approved for use by all Departments and Agencies of the Department of Defense.
MIL-DTL-27500H (NOTICE 1), MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (16 APR 2001) (SUPERSEDING MIL-C-27500G)
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H (NOTICE 1), MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (16 APR 2001) (SUPERSEDING MIL-C-27500G)., MIL-DTL-27500H, dated 10 December 1997, is hereby canceled. Future acquisitions for this material should refer to National Electrical Manufacturers Association (NEMA) WC 27500, Standard for Aerospace and Industrial Electric Cable.
MIL-DTL-27500H, MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500)
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H, MILITARY SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (S/S BY NEMA-WC27500) (10 December 1997) (SUPERSEDING MIL-C-27500G)., This specification covers the requirements for special purpose and power electrical cable. (see 6.1)
MIL-DTL-27500H, DETAIL SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR
Ident. Num:
MIL-DTL-27500 
  Rev. Num:

MIL-DTL-27500H, DETAIL SPECIFICATION CABLE, POWER, ELECTRICAL AND CABLE SPECIAL PURPOSE, ELECTRICAL SHIELDED AND UNSHIELDED, GENERAL SPECIFICATION FOR (10 DEC 1997)., This specification covers the requirements for special purpose and power electrical cable. (see 6.1)
MIL-DTL-2845E, PROPULSION SYSTEMS, BOAT AND SHIP; MAIN SHAFTING, PROPELLERS, BEARINGS, GAUGES, SPECIAL TOOLS, AND ASSOCIATED REPAIR PARTS; PRESERVATIO
Ident. Num:
MIL-DTL-2845 
  Rev. Num:

MIL-DTL-2845E (sh), DETAIL SPECIFICATION PROPULSION SYSTEMS, BOAT AND SHIP; MAIN SHAFTING, PROPELLERS, BEARINGS, GAUGES, SPECIAL TOOLS, AND ASSOCIATED REPAIR PARTS; PRESERVATION, PACKAGING, PACKING AND STORAGE OF. This specification covers the cleaning, drying, preservation, packing, marking, and storage of main propulsion shafting, line shaft bearings, stern tube and strut bearings, boat and ship propellers, propeller devices including controllable pitch propellers, shafting, and accessories thereto. It also covers repair parts, tools, and independently mounted main propulsion thrust bearings.
MIL-DTL-28619D, DETAIL SPECIFICATION ANCHORS, STATO MOORING, 200 TO 15,000 POUNDS (20 OCT 97)
Ident. Num:
MIL-DTL-28619 
  Rev. Num:

MIL-DTL-28619D, DETAIL SPECIFICATION ANCHORS, STATO MOORING, 200 TO 15,000 POUNDS (20 OCT 97). This specification covers stato mooring anchors, including stabilizers, wedges, and palm extensions.
MIL-DTL-29183/7B, DETAIL SPECIFICATION SHEET PANELBOARD, POWER DISTRIBUTION, PORTABLE, WEATHERPROOF, TYPE I, CLASS 1, CONFIGURATION 5: 480 OR 208 VOLT
Ident. Num:
MIL-DTL-29183 
  Rev. Num:

MIL-DTL-29183/7B, DETAIL SPECIFICATION SHEET PANELBOARD, POWER DISTRIBUTION, PORTABLE, WEATHERPROOF, TYPE I, CLASS 1, CONFIGURATION 5: 480 OR 208 VOLT, 120 KILOWATT, TERMINAL TYPE CONNECTORS (13 MAR 03)., This specification is approved for use by all departments and agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and the issue of MIL-DTL-29183 listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation.
MIL-DTL-29229B (YD), DETAIL SPECIFICATION SWITCHES AND FROGS, TRACK, FABRICATED, FOR PORTAL CRANES (14 MAR 1997) [SUPERSEDING MIL-S-29229A(YD)]
Ident. Num:
MIL-DTL-29229 
  Rev. Num:

MIL-DTL-29229B (YD), DETAIL SPECIFICATION SWITCHES AND FROGS, TRACK, FABRICATED, FOR PORTAL CRANES (14 MAR 1997) [SUPERSEDING MIL-S-29229A(YD)] ., This document covers special fabricated track switches and frogs for portal crane tracks.
MIL-DTL-29395B, DETAIL SPECIFICATION SLACKS, WOMEN'S - MUSICIAN'S (21 OCT 1997) [SUPERSEDING MIL-S-29395A]
Ident. Num:
MIL-DTL-29395 
  Rev. Num:

MIL-DTL-29395B, DETAIL SPECIFICATION SLACKS, WOMEN'S - MUSICIAN'S (21 OCT 1997) [SUPERSEDING MIL-S-29395A]., This specification covers the requirements for slacks for wear by female members of the U.S. Marine Band.
MIL-DTL-29479A (MC), DETAIL SPECIFICATION SLACKS, WOMEN'S (21 OCT 1997) [SUPERSEDING MIL-S-29479 (MC)]
Ident. Num:
MIL-DTL-29479 
  Rev. Num:

MIL-DTL-29479A (MC), DETAIL SPECIFICATION SLACKS, WOMEN'S (21 OCT 1997) [SUPERSEDING MIL-S-29479 (MC)]., This specification covers the requirements for women's slacks.
MIL-DTL-31000A, TECHNICAL DATA PACKAGES (9 JUL 1997)
Ident. Num:
MIL-DTL-31000 
  Rev. Num:

DETAIL SPECIFICATION, TECHNICAL DATA PACKAGES (9 JUL 1997). This specification prescribes the requirements for preparing a technical data package (TDP) which is composed of one or more TDP elements and related TDP data management products (See 6.1). This specification does not apply to financial, management, or contract administrative data.
MIL-DTL-31000C, TECHNICAL DATA PACKAGES (9 JUL 2004)
Ident. Num:
MIL-DTL-31000 
  Rev. Num:

DETAIL SPECIFICATION, TECHNICAL DATA PACKAGES (9 JUL 2004) . This specification prescribes the requirements for preparing a technical data package (TDP), which is composed of one or more TDP elements and related TDP data management products (See 6.1). This specification does not apply to financial, management, or contract administrative data.
MIL-DTL-31011A, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (6 DEC 2000) [SUPERSEDING MIL-PRF-31011 AND MIL-C-44187]
Ident. Num:
MIL-DTL-31011 
  Rev. Num:

MIL-DTL-31011A, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (6 DEC 2000) [SUPERSEDING MIL-PRF-31011 AND MIL-C-44187]., This document covers the requirements for four types of woodland camouflage cloth, which are waterproof, and moisture vapor permeable.
MIL-DTL-31011B, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (10 FEB 2005)
Ident. Num:
MIL-DTL-31011 
  Rev. Num:

MIL-DTL-31011B, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (10 FEB 2005)., This document covers the requirements for four types of camouflage cloth, which are waterproof and moisture vapor permeable.
MIL-DTL-31011B, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (10 FEB 2005)
Ident. Num:
MIL-DTL-31011 
  Rev. Num:

MIL-DTL-31011B, DETAILED SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (10 FEB 2005)., This document covers the requirements for four types of camouflage cloth, which are waterproof and moisture vapor permeable.
MIL-DTL-32258, DETAIL SPECIFICATION NUT, SELF-LOCKING (RING TYPE NON-METALLIC INSERT), HEAVY HEX, CONTROLLED ROOT RADIUS, NICKEL-COPPER ALLOY (28 JUN
Ident. Num:
MIL-DTL-32258 
  Rev. Num:

MIL-DTL-32258, DETAIL SPECIFICATION NUT, SELF-LOCKING (RING TYPE NON-METALLIC INSERT), HEAVY HEX, CONTROLLED ROOT RADIUS, NICKEL-COPPER ALLOY (28 JUN 2007) (SUPERSEDING MIL-N-25027/1A)., This specification covers ring-type, self-locking, heavy hex, nickel-copper alloy nuts, with screw threads with a controlled root radius for use in general shipboard applications. Coarse pitch series and eight pitch series of threads are covered by this specification. Nuts with a nominal diameter between ¼ and 2½ inches are covered in this specification.
MIL-DTL-3432H, DETAIL SPECIFICATION CABLES, (POWER AND SPECIAL PURPOSE) AND WIRE, ELECTRICAL (300 AND 600 VOLTS) (23 JAN 2006)
Ident. Num:
MIL-DTL-3432 
  Rev. Num:

MIL-DTL-3432H, DETAIL SPECIFICATION CABLES, (POWER AND SPECIAL PURPOSE) AND WIRE, ELECTRICAL (300 AND 600 VOLTS) (23 JAN 2006)., This specification covers single and multiple conductor cables with and without shields for use in 300 and 600 volts root mean square (rms) applications (see 6.1).
MIL-DTL-3701D, DETAILED SPECIFICATION CYLINDERS, COMPRESSED GAS: DOT-8 ACETYLENE, WITH VALVES (14 SEP 2007)
Ident. Num:
MIL-DTL-3701 
  Rev. Num:

MIL-DTL-3701D, DETAILED SPECIFICATION CYLINDERS, COMPRESSED GAS: DOT-8 ACETYLENE, WITH VALVES (14 SEP 2007)., This specification covers new steel cylinders, with applicable valves and caps, intended for acetylene service.
MIL-DTL-38999/20 Connectors, Electrical, Circular, Receptacle, Threaded, Wall Mounting Flange, Removable Crimp Contacts, Series III, Metric
Ident. Num:
MIL-DTL-38999/20 
  Rev. Num:

METRIC MIL-DTL-38999/20F 17 May 2007 SUPERSEDING MIL-DTL-38999/20E 11 June 2001 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, CIRCULAR, RECEPTACLE, THREADED, WALL MOUNTING FLANGE, REMOVABLE CRIMP CONTACTS, SERIES III, METRIC This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-38999.
MIL-DTL-38999/26, Connectors, Electrical, Plug, Circulat, Threaded, Straight, Removable Crimp Contacts, Series III, Metric
Ident. Num:
MIL-DTL-38999/26 
  Rev. Num:

METRIC MIL-DTL-38999/26E 11 June 2001 SUPERSEDING MIL-C-38999/26D 7 May 1990 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, PLUG, CIRCULAR, THREADED, STRAIGHT, REMOVABLE CRIMP CONTACTS, SERIES III, METRIC This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification and MIL-DTL-38999.
MIL-DTL-38999K (AMENDMENT 1), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), EN
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (AMENDMENT 1), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (25 MAY 2001)., This amendment forms a part of MIL-DTL-38999K, dated 17 December 1999, and is approved for use by all Departments and Agencies of the Department of Defense.
MIL-DTL-38999K (AMENDMENT 2), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), EN
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (AMENDMENT 2), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (19 APR 2002).,
MIL-DTL-38999K (AMENDMENT 3), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), EN
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (AMENDMENT 3), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (22 AUG 2003)., This amendment forms a part of MIL-DTL-38999K, dated 17 December 1999, and is approved for use by all Departments and Agencies of the Department of Defense.
MIL-DTL-38999K (SUPPLEMENT 1), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), E
Ident. Num:
MIL-DTL-38999 
  Rev. Num:

MIL-DTL-38999K (SUPPLEMENT 1), CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (12 JUL 2002)., This supplement forms a part of MIL-DTL-38999K, dated 17 December 1999.
MIL-DTL-38999K, CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESI
Ident. Num:
MIL-DTL-38999  
  Rev. Num:

MIL-DTL-38999K, CONNECTORS, ELECTRICAL, CIRCULAR, MINIATURE, HIGH DENSITY, QUICK DISCONNECT (BAYONET, THREADED, AND BREECH COUPLING), ENVIRONMENT RESISTANT, REMOVABLE CRIMP AND HERMETIC SOLDER CONTACTS, GENERAL SPECIFICATION FOR (17 DEC 1999)., This specification covers four series of miniature, high density, bayonet, threaded, or breech coupling, circular, environment resistant, electrical connectors using removable crimp or fixed hermetic solder contacts, and are capable of operation within a temperature range of -65 deg. C to +200 deg. C.
MIL-DTL-3922C (w/ AMENDMENT 1)., DETAIL SPECIFICATION FLANGES, WAVEGUIDE, GENERAL PURPOSE, GENERAL SPECIFICATION FOR (24 MAY 2006)
Ident. Num:
MIL-DTL-3922 
  Rev. Num:

MIL-DTL-3922C (w/ AMENDMENT 1)., DETAIL SPECIFICATION FLANGES, WAVEGUIDE, GENERAL PURPOSE, GENERAL SPECIFICATION FOR (24 MAY 2006)., This specification covers the general requirements for general purpose waveguide flanges that are used to couple mechanically and electrically two sections of waveguides or waveguide parts (see 6.2).
MIL-DTL-43342F, DETAIL SPECIFICATION WEBBING ASSEMBLIES, GENERAL SPECIFICATION FOR (25 APR 2005) [SUPERSEDING MIL-W-43342E]
Ident. Num:
MIL-DTL-43342 
  Rev. Num:

MIL-DTL-43342F, DETAIL SPECIFICATION WEBBING ASSEMBLIES, GENERAL SPECIFICATION FOR (25 APR 2005) [SUPERSEDING MIL-W-43342E]., This document covers requirements for miscellaneous cotton and nylon webbing assemblies used in rigging for airdrop operations.
MIL-DTL-43649C, DETAIL SPECIFICATION, PARACHUTES, CARGO, 12, 26, AND 34 FOOT DIAMETER (25 JUN 1997) [SUPERSEDING MIL-P-43649B (GL)]
Ident. Num:
MIL-DTL-43649 
  Rev. Num:

MIL-DTL-43649C, DETAIL SPECIFICATION, PARACHUTES, CARGO, 12, 26, AND 34 FOOT DIAMETER (25 JUN 1997) [SUPERSEDING MIL-P-43649B (GL)]., This specification covers the requirements for three cargo parachute assemblies and the separate components thereof.
MIL-DTL-43649D, DETAIL SPECIFICATION, PARACHUTES, CARGO, 12, 26, AND 34 FOOT DIAMETER (25 APR 2005)
Ident. Num:
MIL-DTL-43649 
  Rev. Num:

MIL-DTL-43649D, DETAIL SPECIFICATION, PARACHUTES, CARGO, 12, 26, AND 34 FOOT DIAMETER (25 APR 2005)., This specification covers the requirements for three cargo parachute assemblies and the separate components thereof.
MIL-DTL-45204D, DETAIL SPECIFICATION GOLD PLATING, ELECTRODEPOSITED (29 June 2007)
Ident. Num:
MIL-DTL-45204 
  Rev. Num:

MIL-DTL-45204D, DETAIL SPECIFICATION GOLD PLATING, ELECTRODEPOSITED (29 June 2007)., (SUPERSEDING MIL-G-45204C 7 June 1983 w/AMENDMENT 3 9 June 1993), This specification covers electrodeposited gold plating on metallic surfaces (see 6.1).
MIL-DTL-45913C, DETAIL SPECIFCATION, NUTS, SELF-LOCKING, HEXAGON, PREVAILING TORQUE (30 APR 1998) (SUPERSEDING MIL-N-45913B]
Ident. Num:
MIL-DTL-45913 
  Rev. Num:

MIL-DTL-45913C, DETAIL SPECIFCATION, NUTS, SELF-LOCKING, HEXAGON, PREVAILING TORQUE (30 APR 1998) (SUPERSEDING MIL-N-45913B]., This specification establishes mechanical and performance requirements for prevailing-torque hexagon locknuts.
MIL-DTL-4M, DETAIL SPECIFICATION TIRES AND INNER TUBES (NON-AIRCRAFT); PACKAGING OF (10 JAN 1997)
Ident. Num:
MIL-DTL-4 
  Rev. Num:

MIL-DTL-4M, DETAIL SPECIFICATION TIRES AND INNER TUBES (NON-AIRCRAFT); PACKAGING OF (10 JAN 1997). This specification covers the preservative, packing, and marking for shipment and storage of: Vehicle (non-aircraft) tires, pneumatic; inner tubes, pneumatic tires; and tires with flaps.
MIL-DTL-5015H (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE, GENERAL SPECIFICATION FOR (18 MAY 2000) (Supers
Ident. Num:
MIL-DTL-5015 
  Rev. Num:

MIL-DTL-5015H (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE, GENERAL SPECIFICATION FOR (18 MAY 2000) (Superseding MIL-C-5015G)., This supplement forms a part of MIL-DTL-5015H, dated 18 May 2000. The documents listed in this supplement have been organized to provide information to assist users with the proper selection of connectors.
MIL-DTL-5015H, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE, GENERAL SPECIFICATION FOR (18 MAY 2000)(SUPERSEDING MIL-C-5015
Ident. Num:
MIL-DTL-5015 
  Rev. Num:

MIL-DTL-5015H, DETAIL SPECIFICATION CONNECTORS, ELECTRICAL, CIRCULAR THREADED, AN TYPE, GENERAL SPECIFICATION FOR (18 MAY 2000)(SUPERSEDING MIL-C-5015G)., This specification is approved for use by all Departments and Agencies of the Department of Defense.. This specification covers circular threaded electrical connectors with solder or removable crimp contacts (both front and rear release). These connectors are for use in electronic, electrical power, and control circuits (see 6.1).
MIL-DTL-5070E, DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (22 SEP 2000) [SUPERSEDING MIL-A-5070D]
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070E, DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (22 SEP 2000) [SUPERSEDING MIL-A-5070D]., This supplement forms a part of MIL-DTL-5070E, dated 22 September 2000.
MIL-DTL-5070F (W/ AMENDMENT 1), DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (30 MAY 2007)
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070F (W/ AMENDMENT 1), DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (30 MAY 2007)., This specification covers general requirements for adapter, hose to tube, pipe, and flange, reusable - hydraulic, fuel, and oil lines.
MIL-DTL-5070F (W/ SUPPLEMENT 1), DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPEC
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070F (W/ SUPPLEMENT 1), DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (15 JUN 2007)., This supplement forms a part of MIL-DTL-5070F, dated 10 December 2006.
MIL-DTL-5070F, DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (10 DEC 2006)
Ident. Num:
MIL-DTL-5070 
  Rev. Num:

MIL-DTL-5070F, DETAIL SPECIFICATION ADAPTER, HOSE TO TUBE, PIPE, AND FLANGE, REUSABLE - HYDRAULIC, FUEL, AND OIL LINES, GENERAL SPECIFICATION FOR (10 DEC 2006) [SUPERSEDING MIL-A-5070D]., This specification covers general requirements for adapter, hose to tube, pipe, and flange, reusable - hydraulic, fuel, and oil lines.
MIL-DTL-53039B, DETAIL SPECIFICATION COATING, ALIPHATIC POLYURETHANE, SINGLE COMPONENT, CHEMICAL AGENT RESISTANT (8 JUN 2005) [SUPERSEDING MIL-C-53039A]
Ident. Num:
MIL-DTL-53039 
  Rev. Num:

MIL-DTL-53039B, DETAIL SPECIFICATION COATING, ALIPHATIC POLYURETHANE, SINGLE COMPONENT, CHEMICAL AGENT RESISTANT (8 JUN 2005) [SUPERSEDING MIL-C-53039A]., This specification covers single component, chemical agent resistant, aliphatic polyurethane coating for use as a finish coat on military combat equipment. The coating is lead and hexavalent chromium free and has a maximum of 420 grams/liter (3.5 pounds/gallon) volatile organic compounds for type I and a maximum of 180 grams/liter (1.5 pounds/gallon) volatile organic compounds with zero volatile hazardous air pollutants for type II.
MIL-DTL-5498F, DETAIL SPECIFICATION ACCUMULATORS, HYDRAULIC, CYLINDRICAL 3000 PSI, AIRCRAFT (22 JAN 2008) (SUPERSEDING
Ident. Num:
MIL-DTL-5498 
  Rev. Num:

MIL-DTL-5498F, DETAIL SPECIFICATION ACCUMULATORS, HYDRAULIC, CYLINDRICAL 3000 PSI, AIRCRAFT (22 JAN 2008) (SUPERSEDING MIL-A-5498E)., This specification covers hydraulic accumulators having a single-shell design with a piston type separator for use in aircraft hydraulic systems at rated pressures ranging to 3,000 pounds per square inch (psi) between the temperature range of -65 degrees F to 275 degrees F.
MIL-DTL-5500E, DETAIL SPECIFICATION CAP, HIGH PRESSURE AIR VALVE (5 NOV 2007)
Ident. Num:
MIL-DTL-5500 
  Rev. Num:

MIL-DTL-5500E, DETAIL SPECIFICATION CAP, HIGH PRESSURE AIR VALVE (5 NOV 2007)., This specification covers one type and grade of high-pressure air valve cap suitable for use in aircraft hydraulic systems.
MIL-DTL-55116C (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR (22 MAR 2004) [SUPERSEDING MIL-C-55116B]
Ident. Num:
MIL-DTL-55116 
  Rev. Num:

MIL-DTL-55116C (SUPPLEMENT 1), DETAIL SPECIFICATION CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR (22 MAR 2004) [SUPERSEDING MIL-C-55116B]., This supplement forms a part of MIL-DTL-55116C, dated 22 March 2004
MIL-DTL-55116C, DETAIL SPECIFICATION CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR (22 MAR 2004) [SUPERSEDING MIL-C-55116B]
Ident. Num:
MIL-DTL-55116 
  Rev. Num:

MIL-DTL-55116C, DETAIL SPECIFICATION CONNECTORS: MINIATURE AUDIO, FIVE-PIN AND SIX-PIN GENERAL SPECIFICATION FOR (22 MAR 2004) [SUPERSEDING MIL-C-55116B]., This specification covers waterproof, polarized, five and six contact electrical connectors (plugs and receptacles) for use in audio frequency circuits at 60 volts maximum potential and 0.5 amperes maximum current.
MIL-DTL-5541F, CHEMICAL CONVERSION COATINGS ON ALUMINUM AND ALUMINUM ALLOYS
Ident. Num:
MIL-DTL-5541 
  Rev. Num:

This specification covers chemical conversion coatings formed by the reaction of chemical conversion materials with the surfaces of aluminum and aluminum alloys.
MIL-DTL-5624U, DETAIL SPECIFICATION TURBINE FUEL, AVIATION, GRADES JP-4 and JP-5 (5 JAN 2004)
Ident. Num:
MIL-DTL-5624 
  Rev. Num:

MIL-DTL-5624U, DETAIL SPECIFICATION TURBINE FUEL, AVIATION, GRADES JP-4 and JP-5 (5 JAN 2004)., This specification covers two grades of aviation turbine fuel NATO F-40 (JP-4) and NATO F-44 (JP-5) (see 6.1).
MIL-DTL-5765G, DETAIL SPECIFICATION, STRAND, WIRE, ARMORED STEEL (5 JAN 1996)
Ident. Num:
MIL-DTL-5765 
  Rev. Num:

MIL-DTL-5765G, DETAIL SPECIFICATION, STRAND, WIRE, ARMORED STEEL (5 JAN 1996)., This specification covers armored steel tow target cable. The terms "strand" and :cable" as referred to in this specification are defined in 6.3.3 and 6.3.1.
MIL-DTL-6000D, DETAIL SPECIFICATION HOSE, RUBBER, AIRCRAFT, FUEL, OIL, COOLANT, WATER, AND ALCOHOL (20 SEP 2007)
Ident. Num:
MIL-DTL-6000 
  Rev. Num:

MIL-DTL-6000D, DETAIL SPECIFICATION HOSE, RUBBER, AIRCRAFT, FUEL, OIL, COOLANT, WATER, AND ALCOHOL (20 SEP 2007)., This specification covers the requirements for hose, rubber, aircraft, fuel, oil, coolant, water, and alcohol, for use in aircraft engine applications.
MIL-DTL-6363H, DETAIL SPECIFICATION LAMPS, INCANDESCENT, AIRCRAFT SERVICE GENERAL SPECIFICATION FOR (30 SEP 1997) (SUPERSEDING MIL-L-6363G)
Ident. Num:
MIL-DTL-6363 
  Rev. Num:

MIL-DTL-6363H, DETAIL SPECIFICATION LAMPS, INCANDESCENT, AIRCRAFT SERVICE GENERAL SPECIFICATION FOR (30 SEP 1997) (SUPERSEDING MIL-L-6363G)., This specification provides the general and environmental performance requirements for incandescent lamps intended for use primarily in military aircraft applications.
MIL-DTL-64159 (INTERIM AMENDMENT 1), DETAIL SPECIFICATION COATING, WATER DISPERSIBLE ALIPHATIC POLYURETHANE, CHEMICAL AGENT RESISTANT (6 MAR 2007)
Ident. Num:
MIL-DTL-64159 
  Rev. Num:

MIL-DTL-64159 (INTERIM AMENDMENT 1), DETAIL SPECIFICATION COATING, WATER DISPERSIBLE ALIPHATIC POLYURETHANE, CHEMICAL AGENT RESISTANT (6 MAR 2007)., This specification covers water-dispersible, chemical agent resistant, aliphatic polyurethane coatings for use as a finish coat on all military tactical equipment, which includes ground, aviation and related support assets. The materials are free of hazardous air pollutants (HAP-free), lead and chromate (hexavalent chromium) free, and have a maximum volatile organic compound (VOC) content of 220 g/L (1.8 lb/gal) as packaged.
MIL-DTL-64159, DETAIL SPECIFICATION COATING, WATER DISPERSIBLE ALIPHATIC POLYURETHANE, CHEMICAL AGENT RESISTANT (30 JAN 2002)
Ident. Num:
MIL-DTL-64159 
  Rev. Num:

MIL-DTL-64159, DETAIL SPECIFICATION COATING, WATER DISPERSIBLE ALIPHATIC POLYURETHANE, CHEMICAL AGENT RESISTANT (30 JAN 2002)., This specification covers water-dispersible, chemical agent resistant, aliphatic polyurethane coatings for use as a finish coat on all military tactical equipment, which includes ground, aviation and related support assets. The materials are free of hazardous air pollutants (HAP-free), lead and chromate (hexavalent chromium) free, and have a maximum volatile organic compound (VOC) content of 220 g/L (1.8 lb/gal) as packaged.
MIL-DTL-6645J, DEPARTMENT OF DEFENSE DETAIL SPECIFICATION, PARACHUTES, PERSONNEL, GENERAL SPECIFICATION FOR (31 AUG 2001) [SUPERSEDING MIL-P-6645H]
Ident. Num:
MIL-DTL-6645 
  Rev. Num:

MIL-DTL-6645J, DEPARTMENT OF DEFENSE DETAIL SPECIFICATION, PARACHUTES, PERSONNEL, GENERAL SPECIFICATION FOR (31 AUG 2001) [SUPERSEDING MIL-P-6645H]., This specification covers the general and specific requirements for personnel parachutes and components thereof, as well as specific manufacturing instructions.
MIL-DTL-71026A (AR), MILITARY SPECIFICATION MAGAZINE, CARTRIDGE, SOFT PACK, REUSABLE, M249, 5.56MM MACHINE GUN, GENERAL SPECIFICATION FOR (6 JUN 2000)
Ident. Num:
MIL-DTL-71026 
  Rev. Num:

MIL-DTL-71026A (AR), MILITARY SPECIFICATION MAGAZINE, CARTRIDGE, SOFT PACK, REUSABLE, M