MIL-PRF-31011, PERFORMANCE SPECIFICATION CLOTH, WATERPROOF AND MOISTURE VAPOR PERMEABLE (18 JAN 1996) [S/S BY MIL-DTL-31011]., This performance specification covers the requirements for woodland camouflage printed cloth which is waterproof and moisture vapor permeable.

MIL-PRF-31031B, PERFORMANCE SPECIFICATION, CONNECTORS, ELECTRICAL, PLUGS AND RECEPTACLES, COAXIAL, RADIO FREQUENCY, HIGH RELIABILITY, FOR FLEXIBLE AND SEMIRIGID CABLES, GENERAL SPECIFICATION FOR (18 AUG 2005) [SUPERSEDING MIL-C-31031]., This specification covers the general requirements and tests for radio frequency connectors used with flexible RF cables and certain other types of coaxial transmission lines.

MIL-PRF-31032, PERFORMANCE SPECIFICATION PRINTED CIRCUIT BOARD/PRINTED WIRING BOARD, GENERAL SPECIFICATION FOR (1 NOV 1995)., This specification establishes the general performance requirements for printed circuit boards or printed wiring boards (hereafter designated printed board) and the verification requirements for insuring that these items meet the applicable performance requirements. Certification and qualification to this specification allows manufacturer's to apply the QML program to printed boards procured to non-QML documents such as MIL-P-55110 and MIL-P-50884 (see 6.3.4 and 6.5). The intent of this specification is to allow the printed board manufacturer the flexibility to implement best commercial practices to the maximum extent possible while still providing product that meets military performance needs (see 6.3.3).

MIL-PRF-31032/1B W/ AMENDMENT 2, PERFORMANCE SPECIFICATION SHEET PRINTED WIRING BOARD, RIGID, MULTILAYERED,THERMOSETTING RESIN BASE MATERIAL, WITH OR WITHOUT BLIND AND BURIED PLATED THROUGH HOLES, FOR SOLDERED PART MOUNTING. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-31032. This specification covers the generic performance requirements for rigid, multilayered (three or more conductor layers) printed wiring boards (hereafter designated printed board) with plated holes, that will use soldering for component/part mounting.

MIL-PRF-31032A (w/AMENDMENT 1), PERFORMANCE SPECIFICATION, PRINTED CIRCUIT BOARD/PRINTED WIRING BOARD, GENERAL SPECIFICATION FOR (24 FEB 2006)., This specification establishes the general performance requirements for printed circuit boards or printed wiring boards (hereafter designated printed board) and the verification requirements for insuring that these items meet the applicable performance requirements. Certification and qualification to this specification allows manufacturer’s to apply the Qualified Manufacturers List (QML) program to printed boards procured to non-QML documents such as MIL-PRF-55110 and MIL-P-50884 (see 6.3.4 and 6.5). The intent of this specification is to allow the printed board manufacturer the flexibility to implement best commercial practices to the maximum extent possible while still providing product that meets military performance needs (see 6.3.3).

MIL-PRF-31033A, PERFORMANCE SPECIFICATION, CAPACITORS, FIXED, CERAMIC DIELECTRIC, HIGH RELIABILITY, DISCOIDAL, GENERAL SPECIFICATION FOR (3 NOV 2003)., This specification covers the requirements for high reliability, discoidal, ceramic dielectric, fixed capacitors. This specification provides for two levels of product requirements: Class B and class S. Capacitors furnished to the requirements of this specification are intended for use in Radio Frequency/ Electromagnetic Interference (RFI/EMI) suppression filters covered by MIL-PRF-28861. This specification establishes a Qualified Manufacturers List (QML) for discoidal capacitors that requires demonstration of control of the quality system and manufacturing process and qualification of representative discoidal capacitor designs.

MIL-PRF-32002C, PERFORMANCE SPECIFICATION, COVER MATERIAL, VEHICLE, COATED TACTICAL AND COMBAT, HEAVY-DUTY, WATERPROOF (29 AUG 2000)., This specification covers the requirements for heavy-duty, waterproof, coated tactical and combat vehicle cover material, known hereinafter as “cover material” (see 6.1).

MIL-PRF-32014A, PERFORMANCE SPECIFICATION, GREASE, AIRCRAFT AND INSTRUMENT (12 SEP 2006)., This specification covers the general requirements for a multipurpose, water resistant, high speed grease for use in the -54oC to +177oC temperature range.

MIL-PRF-32016A(EA), PERFORMANCE SPECIFICATION, CELL, GAS PHASE, ADSORBER (22 APR 2002)., This specification covers gas phase adsorber cells used to remove toxic chemical vapors exhausted from laboratory air filtration systems. This specification does not include requirements for the housing into which these adsorber cells are installed.

MIL-PRF-32017, PERFORMANCE SPECIFICATION, REFRIGERATION SYSTEM, ADVANCED DESIGN (1 DEC 1997)., This specification covers the performance requirements for an Advanced Design Refrigeration (ADR) system consisting of an Insulated Container (IC) and an electrically driven Refrigeration Unit (RU).

MIL-PRF-32029 (AMENDMENT 1), PERFORMANCE SPECIFICATION AUTOMATED CONFIGURATION MANAGEMENT SYSTEM (ACMS) (14 DEC 1998)., This amendment forms a part of Mil-Prf-32029, dated 30 June 1998, is approved for use by all Departments and Agencies of the Department of Defense.

MIL-PRF-32029(AMENDMENT 1), PERFORMANCE SPECIFICATION AUTOMATED CONFIGURATION MANAGEMENT SYSTEM (ACMS) (14 DEC 1998)., This amendment forms a part of Mil-Prf-32029, dated 30 June 1998, is approved for use by all Departments and Agencies of the Department of Defense.

MIL-PRF-32029(MI), PERFORMANCE SPECIFICATION AUTOMATED CONFIGURATION MANAGEMENT SYSTEM (ACMS) (30 JUN 1998)., This specification covers performance requirements for the U.S. Army’s Automated Configuration Management System (ACMS). It defines the functional requirements for ACMS, interface characteristics, and the environment in which it must operate.

MIL-PRF-32029(MI), PERFORMANCE SPECIFICATION, AUTOMATED CONFIGURATION MANAGEMENT SYSTEM (ACMS) (30 JUN 1998)., This specification covers performance requirements for the U.S. Army’s Automated Configuration Management System (ACMS). It defines the functional requirements for ACMS, interface characteristics, and the environment in which it must operate.

MIL-PRF-32033 (w/AMENDMENT 2), PERFORMANCE SPECIFICATION LUBRICATING OIL, GENERAL PURPOSE, PRESERVATIVE (WATER-DISPLACING, LOW TEMPERATURE) (11 JUL 2006)., This specification covers one type and grade of water-displacing, preservative lubricating oil, known hereinafter as “oil”, for general purpose applications at low temperatures. The oil can be applied by dipping, brushing, or by spraying from gas-pressurized cans. The oil is identified by Military Symbol PL-S and NATO Code Number O-190.

MIL-PRF-32046, PERFORMANCE SPECIFICATION RATION HEATING UNIT, FIELD FEEDING (1 JUL 2003)., This specification covers a ration unit used for heating unitized group rations.

MIL-PRF-32076 (AR), PERFORMANCE SPECIFICATION FOR UTILIZATION OF AMMUNITION (1 DEC 2000). This specification covers the minimum unitization requirements for procurement of packaged ammunition items on 4 way entry pallets used by the Department of Defense, United States Government.

MIL-PRF-32085 (AMENDMENT 1), RELAYS, ELECTROMAGNETIC, 270 V DC, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (15 APR 2002).

MIL-PRF-32085, RELAYS, ELECTROMAGNETIC, 270 V DC, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (16 JUL 2001)., This specification covers the general requirements for electromagnetic relays with main contact ratings of 5 amperes and above at 270 V dc and auxiliary contacts and coil voltage as specified for use in electrical applications. Relays covered by this specification are capable of meeting the electrical and environmental requirements when mounted directly to the structure of aircraft, missile, spacecraft, ship, and other primary vehicles or in ground support and shipboard equipment as well as when used within other subsystems such as electrical load management centers or power controllers.

MIL-PRF-32118, PERFORMANCE SPECIFICATION, VECTOR PRODUCT FORMAT (VPF) DATABASE UPDATE (VDU) (20 MAR 2003)., This specification defines requirements for the National Imagery and Mapping Agency's (NIMA) Vector Product Format (VPF) Database Update (VDU). This specification further defines the tables that are necessary to build an "update layer" for NIMA Vector Product Format (VPF) data sets that require tracking and accountability for changes made to the underlying VPF data set.

MIL-PRF-32140, PERFORMANCE SPECIFICATION, RELAYS, ELECTROMAGNETIC, RADIO FREQUENCY, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (14 JAN 2004)., This specification covers the general requirements for electromagnetic, RF hermetically sealed relays for use in electronic and communication-type equipment (see 6.1). These relays are designed to operate over the full range from low level to power switching with contact ratings up to 1 ampere direct current (dc). The failure rate level is established at a confidence level of 95 percent based on 1 million to 20 million cycles (see 1.3) at maximum ambient temperature (see 3.1).

MIL-PRF-32171A, PERFORMANCE SPECIFICATION, DECK COATINGS, HIGH DURABILITY (30 MAR 2006)., This specification establishes the requirements for high durability, wear resistant deck coatings for use in high traffic areas, with minimal maintenance.

MIL-PRF-32177, PERFORMANCE SPECIFICATION, CLEANING COMPOUND, FLIGHT DECK (27 SEP 2004)., This specification establishes the requirements for a compound for cleaning flight deck surfaces on aircraft carriers and other air-capable ships.

MIL-PRF-32181, PERFORMANCE SPECIFICATION TRUCK, FORKLIFT, 4,000 AND 6,200 POUND CAPACITY, LOADING, INTERNAL COMBUSTION ENGINE (14 DEC 2004)., This specification covers a commercial, sit-down rider, diesel-engine-driven, counter-balanced forklift truck (hereinafter called the truck). The truck will have a telescopic mast, front wheel drive, power steering, hydraulic brakes, pneumatic tires, and an overhead guard.

MIL-PRF-32207, PERFORMANCE SPECIFICATION PROPELLANT, METHANE (10 OCT 2006)., This specification covers two types and three grades of propellant methane.

MIL-PRF-32216, PERFORMANCE SPECIFICATION EVALUATION OF COMMERCIAL OFF-THE-SHELF (COTS) MANUALS AND PREPARATION OF SUPPLEMENTAL DATA (17 OCT 2006)., This specification provides criteria for evaluating commercial off-the-shelf (COTS) manuals for acceptance. It also provides requirements for preparing supplemental data to COTS manuals. In this specification, the term "manual" means the same as COTS or COTS manual.

MIL-PRF-32239, PERFORMANCE SPECIFICATION, COATING SYSTEM, ADVANCED PERFORMANCE, FOR AEROSPACE APPLICATIONS. This specification establishes the requirements for coating systems having high durability to be used in finishing aircraft exterior surfaces. These coating systems normally are comprised of a surface treatment, a primer, and a topcoat and include a chemical stripper and a cleaning compound for topcoat washing.

MIL-PRF-32269, PERFORMANCE SPECIFICATION, PERFORATED HOMOGENEOUS STEEL ARMOR (18 OCT 2007)., This specification covers perforated homogeneous steel appliqué armor in nominal thicknesses from 0. 250 - 2.000 inch, inclusive.

MIL-PRF-38311C, PERFORMANCE SPECIFICATION MANUALS, TECHNICAL: OPERATION AND ASSOCIATED CHECKLIST (INTERCONTINENTAL BALLISTIC MISSILE) PREPARATION OF (9 DEC 1997) [SUPERSEDING MIL-M-38311B].,

MIL-PRF-38314 (USAF), PERFORMANCE SPECIFICATION MANUALS, TECHNICAL: OPERATION AND ASSOCIATED CHECKLIST (SPACE SYSTEMS), PREPARATION OF (18 AUG 1997)., This specification covers requirements for the preparation of operation manuals and associated checklists for space systems, to include satellite systems, warning systems, surveillance systems, and spacelift systems.

MIL-PRF-38534D, PERFORMANCE SPECIFICATION HYBRID MICROCIRCUITS, GENERAL SPECIFICATION FOR. This specification establishes the general performance requirements for hybrid microcircuits, Multi-Chip Modules (MCM) and similar devices and the verification requirements for insuring that these devices meet the applicable performance requirements. Verification is accomplished through the use of one of two quality programs (Appendix A). The main body of this specification describes the performance requirements and the requirements for obtaining a Qualified Manufacturers List (QML) listing. The appendices of this specification are intended for guidance to aid a manufacturer in developing their verification program. Detail requirements, specific characteristics, and other provisions which are sensitive to the particular intended use should be specified in the applicable device acquisition specification.

MIL-PRF-38534E, GENERAL SPECIFICATION - HYBRID MICROCIRCUITS. This specification establishes the general performance requirements for hybrid microcircuits, Multi- Chip Modules (MCM) and similar devices and the verification requirements for ensuring that these devices meet the applicable performance requirements. Verification is accomplished through the use of one of two quality programs (Appendix A). The main body of this specification describes the performance requirements and the requirements for obtaining a Qualified Manufacturers List (QML) listing. The appendices of this specification are intended for guidance to aid a manufacturer in developing their verification program. Detail requirements, specific characteristics, and other provisions that are sensitive to the particular intended use should be specified in the applicable device acquisition specification.

MIL-PRF-38535E, PERFORMANCE SPECIFICATION INTEGRATED CIRCUITS (MICROCIRCUITS) MANUFACTURING, GENERAL SPECIFICATION FOR. This specification establishes the general performance requirements for integrated circuits or microcircuits and the quality and reliability assurance requirements which must be met for their acquisition. The intent of this specification is to allow the device manufacturer the flexibility to implement best commercial practices to the maximum extent possible while still providing product which meets the military performance needs. Detail requirements, specific characteristics of microcircuits, and other provisions which are sensitive to the particular use intended will be specified in the device specification. Quality assurance requirements outlined herein are for all microcircuits built on a manufacturing line which is controlled through a manufacturer's Quality Management (QM) program and has been certified and qualified in accordance with requirements herein. Several levels of product assurance including Radiation Hardness Assurance (RHA) are provided for in this specification. The certification and qualification sections found herein outline the requirements to be met by a manufacturer to be listed on a Qualified Manufacturer Listing (QML). After listing of a technology flow on a QML, the manufacturer must continually meet or improve the established baseline of certified and qualified procedures, the QM program, the manufacturer's review system, the status reporting and quality and reliability assurance requirements for all QML products. The manufacturer may present alternate methods of addressing the requirements contained in this document. This specification requires a manufacturer to establish a process flow baseline. If sufficient quality and reliability data is available, the manufacturer, through the QM program and the manufacturer's review system, may modify substitute or delete tests.

MIL-PRF-38535F, PERFORMANCE SPECIFICATION INTEGRATED CIRCUITS (MICROCIRCUITS) MANUFACTURING, GENERAL SPECIFICATION FOR. This specification establishes the general performance requirements for integrated circuits or microcircuits and the quality and reliability assurance requirements, which must be met for their acquisition. The intent of this specification is to allow the device manufacturer the flexibility to implement best commercial practices to the maximum extent possible while still providing product that meets military performance needs. Detail requirements, specific characteristics of microcircuits, and other provisions which are sensitive to the particular use intended will be specified in the device specification. Quality assurance requirements outlined herein are for all microcircuits built on a manufacturing line which is controlled through a manufacturer's Quality Management (QM) program and has been certified and qualified in accordance with requirements herein. Several levels of product assurance including Radiation Hardness Assurance (RHA) are provided for in this specification. The certification and qualification sections found herein outline the requirements to be met by a manufacturer to be listed on a Qualified Manufacturer Listing (QML). After listing of a technology flow on a QML, the manufacturer must continually meet or improve the established baseline of certified and qualified procedures, the QM program, the manufacturer's review system, the status reporting and quality and reliability assurance requirements for all QML products. The manufacturer may present alternate methods of addressing the requirements contained in this document. This specification requires a manufacturer to establish a process flow baseline. If sufficient quality and reliability data is available, the manufacturer, through the QM program and the manufacturer's review system, may modify, substitute or delete tests. Class T is not for use in National Aeronautics and Space Administration (NASA) manned, satellite, or launch vehicle programs without written permission from the applicable NASA Project Office (i.e., cognizant electrical, electronic, and electromechanical (EEE) parts authority).

MIL-PRF-38793B, PERFORMANCE SPECIFICATION TECHNICAL MANUALS: CALIBRATION PROCEDURES - PREPARATION (6 FEB 1997)., This performance specification covers the requirements for preparing technical manuals containing manual or automated calibration procedures. It does not apply to calibration procedures written for the exclusive use of the service’s primary standards laboratories.

MIL-PRF-38793C, PERFORMANCE SPECIFICATION TECHNICAL MANUALS: CALIBRATION PROCEDURES - PREPARATION (19 AUG 2008)., This performance specification covers the requirements for preparing technical manuals containing manual or automated calibration procedures. It does not apply to calibration procedures written for the exclusive use of the service’s primary standards laboratories.

MIL-PRF-39001D, PERFORMANCE SPECIFICATION, CAPACITORS, FIXED, MICA DIELECTRIC, ESTABLISHED RELIABILITY AND NONESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (2 MAR 2004)., This specification covers the general requirements for established reliability (ER) and nonestablished reliability (non-ER), mica dielectric, fixed capacitors (see 6.1). The ER capacitors have a failure rate level (FRL) ranging from 1.0 percent per 1,000 hours to 0.001 percent per 1,000 hours (see 1.2.1.7). The FRL is established at a 90 percent confidence level. The FRL, identified by the applicable symbol specified in table V is referred to operational life at full rated voltage (see 1.2.1.6) at 125C or 150C, as applicable. An acceleration factor of 25:1 has been used to relate the life test at 150 percent of rated voltage at rated temperature to rated voltage at rated temperature.”

MIL-PRF-39010E (SUPPLEMENT 1), PERFORMANCE SPECIFICATION COIL, RADIO FREQUENCY, FIXED, MOLDED, ESTABLISHED RELIABILITY AND NONESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (27 AUG 1997) [SUPERSEDING MIL-C-39010D].

MIL-PRF-39010E, PERFORMANCE SPECIFICATION COIL, RADIO FREQUENCY, FIXED, MOLDED, ESTABLISHED RELIABILITY AND NONESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (27 AUG 1997) [SUPERSEDING MIL-C-39010D]., This specification covers the general requirements for established reliability (ER) and nonestablished reliability (non-ER) fixed, radio frequency, molded coils. Established reliability radio frequency coils covered by this specification have failure rate levels (FRL) ranging from 1.0 percent per 1,000 hours to 0.001 percent per 1,000 hours which are established at a 60 percent confidence level (see 1.2.1.4). The FRL identified by the applicable symbol specified in table III refers to operation at full load cyclic condition at the specified ambient temperature (see 3.1).

MIL-PRF-39012/16H, PERFORMANCE SPECIFICATION SHEET CONNECTORS, PLUGS, ELECTRICAL, COAXIAL RADIO FREQUENCY, (SERIES BNC (CABLED), PIN CONTACT, CLASS 2) (16 NOV 2006). The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-39012.

MIL-PRF-39016F (SUPPLEMENT 1), PERFORMANCE SPECIFICATION RELAYS, ELECTROMAGNETIC, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (1 NOV 2002) [SUPERSEDING MIL-R-39016D]., This supplement forms a part of MIL-PRF-39016F, dated 1 November 2002.

MIL-PRF-39016F (w/AMENDMENT 1), PERFORMANCE SPECIFICATION, RELAYS, ELECTROMAGNETIC, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (26 SEP 2005) [SUPERSEDING MIL-R-39016D]., This specification covers the general requirements for electromagnetic, hermetically sealed relays for use in electronic and communication-type equipment (see 6.1). These relays are designed to operate over the full range from low level to power switching with contact ratings up to 5 amperes alternating current (ac) or direct current (dc). The failure rate level is established at a confidence level of 90 percent for qualification and 60 percent for maintenance of qualification based on 100,000 cycles at +125°C under the rated load conditions specified herein. CAUTION: The use of any coil voltage less than the rated coil voltage will compromise the operation of the relay. CAUTION: Pick-up, hold, and dropout voltages are for test purposes only and are not to be used as design criteria. For additional application and caution information, see 6.1.

MIL-PRF-39016F, PERFORMANCE SPECIFICATION RELAYS, ELECTROMAGNETIC, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (1 NOV 2002) [SUPERSEDING MIL-R-39016D]., This specification covers the general requirements for electromagnetic, hermetically sealed relays for use in electronic and communication-type equipment (see 6.1). These relays are designed to operate over the full range from low level to power switching with contact ratings up to 5 amperes alternating current (ac) or direct current (dc). The failure rate level is established at a confidence level of 90 percent for qualification and 60 percent for maintenance of qualification based on 100,000 cycles at +125°C under the rated load conditions specified herein. CAUTION: The use of any coil voltage less than the rated coil voltage will compromise the operation of the relay. CAUTION: Pick-up, hold, and dropout voltages are for test purposes only and are not to be used as design criteria. For additional application and caution information, see 6.1.

MIL-PRF-44408C, PERFORMANCE SPECIFICATION, SHELTER, ELECTRICAL EQUIPMENT, LIGHTWEIGHT (31 OCT 1996) [SUPERSEDING MIL-S-44408B]., This document covers three types of lightweight electrical equipment shelters designed for transport on both the M1037 and M1097 High Mobility Multipurpose Wheeled Vehicle (HMMWV). These shelters are transported by rail, air, marine and highway when mounted or dismounted from their vehicles.

MIL-PRF-46010F, PERFORMANCE SPECIFICATION LUBRICANT, SOLID FILM, HEAT CURED, CORROSION INHIBITING (10 AUG 2000) (SUPERSEDING MIL-L-0046010E)., This specification covers corrosion inhibiting, heat cured, solid film lubricants, hereinafter referred to as “lubricants”, for the reduction of wear and prevention of galling, corrosion, and seizure of metals (see 6.1).

MIL-PRF-46103E, PERFORMANCE SPECIFICATION, ARMOR: LIGHTWEIGHT, COMPOSITE (6 JAN 1998) [SUPERSEDING MIL-A-46103D]., This specification covers the performance requirements for lightweight composite armor (see 6.1).

MIL-PRF-46108C (NOTICE 1), PERFORMANCE SPECIFICATION ARMOR: TRANSPARENT (22 APR 2004) (SUPERSEDING MIL-A-46108B)., This specification covers the performance requirements for transparent armor used in armored military vehicles and aircraft. Transparent armor is the technical term for protective transparencies commonly called ballistic resistant windows.

MIL-PRF-46147C, PERFORMANCE SPECIFICATION LUBRICANT, SOLID FILM, AIR CURED (CORROSION INHIBITING) (18 JAN 2001)., This specification covers two types of corrosion inhibiting, air cured, solid film lubricants, hereafter known as "lubricants," which provide both lubrication and corrosion protection (see 6.1).

MIL-PRF-46176B, PERFORMANCE SPECIFICATION BRAKE FLUID, SILICONE, AUTOMOTIVE, ALL-WEATHER, OPERATIONAL AND PRESERVATIVE (10 JAN 2001) [SUPERSEDING MIL-B-46176A]., This specification covers silicone-based hydraulic brake fluid for use in hydraulic brake systems at ambient temperatures ranging from +55°C to -55°C. The fluid is identified by military symbol BFS and NATO code No. H-547 (see 6.1).

MIL-PRF-46187A, PERFORMANCE SPECIFICATION PREPREG, UNIDIRECTIONAL TAPE, CARBON (GRAPHITE) FIBER HIGH TEMPERATURE RESIN IMPREGNATED, 316°C (600°F) (14 AUG 1998) [SUPERSEDING MIL-P-46187]., This specification establishes the requirements for carbon fiber/high temperature resin prepreg in the form of unidirectional tape suitable for the fabrication of structural laminates intended for use at temperatures up to and including 316°C (600°F) (see 6.1).

MIL-PRF-49118B (CR), PERFORMANCE SPECIFICATION RADIO SET, AN/PRC-70( ) and (UNITS OF) (3 JUL 1997)., This performance specification covers the Radio Set, AN/PRC-70 and units of the set.

MIL-PRF-49506, PERFORMANCE SPECIFICATION LOGISTICS MANAGEMENT INFORMATION (11 NOV 1996)., This specification describes information required by the government to perform acquisition logistics management functions. The principle focus of this specification is on providing the DOD with a contractual method for acquiring support and support-related engineering and logistics data from contractors. The DOD uses this data in-house in existing DOD materiel management processes such as those for initial provisioning, cataloging, and item management. Data products intended primarily for in-house use by the contractor during his/her own design process or those developed internally by the DOD are beyond the scope of this document. Depending on specific program requirements, this information may be in the form of summary reports, a set of specific data products, or both. This specification identifies content requirements for information summaries and format requirement for data products. It may be used on all system/end item acquisition programs. The contractor may, and is encouraged to, suggest alternative means of satisfying requirements of this specification to make information more readily available and to utilize more efficient business practices. The mechanics of delivery (e.g., electronic data interchange, hard copy, etc.) are not within the scope of this specification and should be addressed separately. Data entry media, storage, and maintenance procedures are left to the contractor.

MIL-PRF-52308J, PERFORMANCE SPECIFICATION FILTER-COALESCER ELEMENT, FLUID PRESSURE. This specification covers filter-coalescer elements for use in filter-separator vessels for handling liquid petroleum fuels (see 6.1).

MIL-PRF-52747F, NOZZLE ASSEMBLY, CLOSED-CIRCUIT REFUELING, STANDARD AND ARCTIC SERVICE. This specification covers two types of closed-circuit fuel servicing nozzle assemblies.

MIL-PRF-52748F (NOTICE 1), PERFORMANCE SPECIFICATION NOZZLE, ADAPTER, CLOSED-CIRCUIT TO GRAVITY FILL, STANDARD AND ARCTIC SERVICE. MIL-PRF-52748F, dated 8 December 1995, has been reviewed and determined to be valid for use in acquisition.

MIL-PRF-52955C, PERFORMANCE SPECIFICATION, IMPROVED POSITION AND AZIMUTH DETERMINING SYSTEM (IPADS) (8 NOV 2002) [SUPERSEDING MIL-P-52955A]., This specification covers an inertial surveying system that is air and ground vehicle mounted.

MIL-PRF-53134, PERFORMANCE SPECIFICATION, ULTRA-LIGHTWEIGHT CAMOUFLAGE NET SYSTEM (ULCANS) (26 JAN 1996)., This specification covers the ultra-lightweight camouflage net systems (ULCANS) for tactical equipment and field installations including helicopters and fixed wing aircraft.

MIL-PRF-55110. PERFORMANCE SPECIFICATION PRINTED WIRING BOARD, RIGID GENERAL SPECIFICATION FOR. This specification establishes the performance and qualification requirements for rigid single-sided, double-sided, and multilayer printed wiring boards with or without plated through holes (see 6.1). Verification is accomplished through the use of one of two methods of product assurance (appendix A or appendix B). Detail requirements, specific characteristics, and other provisions which are sensitive to the particular intended use are specified in the applicable master drawing. [Inactive for new design after 31 December 1997. For new design use MIL-PRF-31032.]

MIL-PRF-55365F, PERFORMANCE SPECIFICATION, CAPACITOR, FIXED, ELECTROLYTIC (TANTALUM), CHIP, ESTABLISHED RELIABILITY AND NONESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR (16 APR 2004)., This specification covers the general requirements for nonestablished reliability (non-ER) and established reliability (ER), tantalum dielectric, fixed chip capacitors, primarily intended for use in thick and thin film hybrid circuits or surface mount applications for filter, bypass, coupling, and other applications where the alternating current (ac) component is small compared to the direct current (dc), rated voltage and where supplemental moisture protection is available (see 6.1). The established reliability capacitors have reliability ratings established on the basis of life tests performed at specified voltage at +85C for failure rate levels (FRL) ranging from:

MIL-PRF-55514F, PERFORMANCE SPECIFICATION, CAPACITORS, FIXED, PLASTIC (OR METALLIZED PLASTIC) DIELECTRIC, DC OR DC-AC, IN NONMETAL CASES, NON-ESTABLISHED AND ESTABLISHED RELIABILITY GENERAL SPECIFICATION FOR (15 DEC 2005)., This specification covers the general requirements for established reliability (ER) and non-established reliability (non-ER), (product level C), plastic (or metallized plastic) dielectric, fixed capacitors, enclosed in nonmetal cases intended primarily, in view of the limited long term moisture resistant characteristics, for use in potted or encapsulated systems, in blocking, filter, and by-pass applications (see 6.4). ER capacitors covered by this specification have failure rate levels (M, P, R, and S) ranging from 1.0 percent to 0.001 percent per 1,000 hours. These failure rates (FR) are established at a 90-percent confidence level and maintained at a 10-percent producer’s risk and based on life tests performed at +85°C or +105°C, whichever is applicable. An acceleration factor of 5:1 has been used to relate life test data obtained at 125 percent, or 140 percent of rated voltage at +85°C or +105°C, whichever is applicable, to rated voltage at +85°C or +105°C, whichever is applicable. The product levels are based on catastrophic failures and failures occurring outside the degradation limits.

MIL-PRF-55585G(CR), PERFORMANCE SPECIFICATION ELECTRONICS EQUIPMENT AND PARTS, PACKAGING OF (9 OCT 1997)., This specification covers the packing and marking requirements for use in acquisition documents, contracts, or orders, for electronics equipment and parts containing packaging requirement codes, special packaging instructions, and specifications.

MIL-PRF-55629C, PERFORMANCE SPECIFICATION, CIRCUIT BREAKERS, MAGNETIC, UNSEALED OR PANEL SEAL,TRIP-FREE, GENERAL SPECIFICATION FOR (9 OCT 1997)., This specification covers the requirements and test procedures for single and multipole, trip-free, unsealed, magnetic circuit breakers with current ratings of 0.2 amperes to 100 amperes inclusive, up to and including 240 volts, 400 Hertz, 480 volts, 60 Hertz alternating current (ac) and 125 volts direct current (dc), (see 6.1). These circuit breakers may also include auxiliary contacts (see 6.5.1) for monitoring circuits. A voltage sensitive pole is also available in a four pole device. Panel seal mounts are available in 0.2 amperes through 50 amperes.

MIL-PRF-55681/2C, PERFORMANCE SPECIFICATION SHEET, CAPACITORS, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY STYLE CDR05 (3 JUL 1997)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55681.

MIL-PRF-55681/3D, PERFORMANCE SPECIFICATION SHEET, CAPACITORS, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY STYLE CDR06 (3 JUL 1997)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55681.

MIL-PRF-55681/4E, PERFORMANCE SPECIFICATION SHEET, CAPACITORS, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY STYLES CDR11, CDR12, CDR13, AND CDR14 (HIGH FREQUENCY) (3 JUL 1997)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55681.

MIL-PRF-55681/5D, PERFORMANCE SPECIFICATION SHEET, CAPACITORS, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY STYLES CDR21, CDR22, CDR23, CDR 24, AND CDR25 (HIGH FREQUENCY) (3 JUL 1997)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55681.

MIL-PRF-55681/7B, PERFORMANCE SPECIFICATION SHEET, CAPACITORS, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY STYLE CDR31, METRIC (3 JUL 1997)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55681.

MIL-PRF-55681/8B, PERFORMANCE SPECIFICATION SHEET, CAPACITORS, CHIP, MULTIPLE LAYER, FIXED, CERAMIC DIELECTRIC, ESTABLISHED RELIABILITY AND NON-ESTABLISHED RELIABILITY STYLE CDR32, METRIC (3 JUL 1997)., This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55681.

MIL-PRF-61002B, PERFORMANCE SPECIFICATION, PRESSURE-SENSITIVE ADHESIVE LABELS FOR BAR CODING (30 JUN 2008)., This specification covers the requirements for pressure-sensitive adhesive labels that meet or exceed the end user’s necessary performance criteria for use in the implementation of bar code marking/reading operations.

MIL-PRF-62048C, SUPERSEDING MIL-A-62048B(AT), AIR CLEANERS, AUTOMOTIVE: HEAVY DUTY,DRY-TYPE (FOR INTERNAL COMBUSTION ENGINES) (METRIC), This specification covers heavy duty, dry-type, air cleaners with a replacement filter element for use with internal combustion engines fox

MIL-PRF-62140B, PERFORMANCE SPECIFICATION, ENGINE, DIESEL: LIQUID-COOLED, V-TYPE, 6-CYLINDER, 210 H.P. (25 APR 1997) [SUPERSEDING MIL-E-62140A(AT)]., This specification covers a 210 horsepower, 6-cylinder, V-type, liquid-cooled,internal-combustion, compression-ignition (diesel) engine for use in military vehicles.

MIL-PRF-62195D PERFORMANCE SPECIFICATION RECOVERY VEHICLE, FULL-TRACKED: MEDIUM, M88A1 NEW AND OVERHAUL (29 JAN 1998) [SUPERSEDING MIL-R-62195C(AT)]., This specification covers the requirements and inspections for the M88A1 armored, full-tracked, rear sprocket driven recovery vehicles, both new and overhauled.

MIL-PRF-62419A, PERFORMANCE SPECIFICATION COMPOSITE MATERIALS FOR MILITARY VEHICLES (22 JAN 1996)., This specification covers commercial plastics for use as a replacement of wood components, such as troop slats, seat racks, stakes, and planks, in military vehicles.

MIL-PRF-62540A, PERFORMANCE SPECIFICATION, HARNESS AND CABLE ASSEMBLIES (26 JUL 1996) [SUPERSEDING MIL-H-62540(AT)]., This specification covers the general requirements for electrical harness and cable assemblies.

MIL-PRF-63004D (TM), PERFORMANCE SPECIFICATION MANUALS, TECHNICAL: PREPARATION OF LUBRICATION ORDERS (23 JUN 2006) [SUPERSEDING MIL-M-63004C]., This specification contains requirements for the preparation of lubrication orders (LOs). This specification is applicable to separate, card-form lubrication orders (LOs) only. Lubrication instructions to be incorporated into the maintenance manual should be prepared using MIL-STD-40051-1 or MIL-STD-40051-2.

MIL-PRF-63012B, PERFORMANCE SPECIFICATION MANUALS, TECHNICAL: DEPOT MAINTENANCE WORK REQUIREMENTS (DMWRs) FOR MAINTENANCE/DEMILITARIZATION OF CONVENTIONAL AND CHEMICAL AMMUNITION (20 APR 1998)., This specification contains requirements for preparation of Depot Maintenance Work Requirements (DMWRs) for the maintenance and/or demilitarization of conventional and chemical ammunition, hereafter referred to as ammunition.

MIL-PRF-63029F (AV), TECHNICAL MANUAL SPECIFICATION MANUALS, TECHNICAL: REQUIREMENTS FOR OPERATOR'S MANUALS AND CHECKLISTS FOR AIRCRAFT. This specification establishes the requirements needed to prepare digital technical manuals (TMs) describing operating procedures, checklists, and maintenance test flight (MTF) manuals for operators of Army aircraft.

MIL-PRF-63034B(TM), PERFORMANCE SPECIFICATION BULLETINS, TECHNICAL: WARRANTY, PREPARATION OF. This specification contains requirements for the preparation of warranty technical bulletins (WTBs).

MIL-PRF-63045B (TM), PERFORMANCE SPECIFICATION MANUALS, TECHNICAL: PREPARATION OF DEPOT MANUALS FOR DEPOT TEST, MEASUREMENT AND DIAGNOSTIC EQUIPMENT (17 JUL 1997)., This specification contains the requirements for the preparation of depot manuals (DM) covering operation, maintenance, and calibration procedures for depot test, measurement and diagnostic equipment (TMDE). These requirements are applicable to manuals for equipment which is used for diagnostic and acceptance testing of field equipment items returned to the depot for reconditioning.